(812) 309-78-59
(495) 223-46-76
ASTM A1063/A1063M-11a
Standard Specification for Steel Sheet, Twin-Roll Cast, Zinc-Coated (Galvanized) by the Hot-Dip Process
11 стр.
Заменен
Электронный (pdf)Печатное издание
107.64 $ (включая НДС 20%)
Разработчик:
Зарубежные/ASTM
ICS:
77.140.50 Flat. Including plate, sheet and strip / Стальной листовой прокат и полуфабрикаты. Включая плиты, листы и полосы
Сборник (ASTM):
01.06 Coated Steel Products / Изделия из облицовочной стали
Тематика:
Steel--Structural, Tubes, Plate, Coated
Описание
Реферат

This specification covers coils and cut lengths of steel sheets produced by the twin-roll cast process and zinc-coated (galvanized) by the hot-dip process. The material is available in several designations, categorized broadly as commercial steel (CS Types A, B, and C), structural steel (SS), and high strength low alloy steel (HSLAS). Steel samples shall undergo heat analysis and adhere to chemical composition requirements based on their respective designations. Materials shall also conform to yield strength, tensile strength, and elongation requirements in accordance to grade, class, or both. Zinc coatings shall be tested and conform to weight/mass and bending requirements in relation to coating thickness.

Область применения

1.1 This specification covers steel sheet, produced by the Twin-Roll Cast Process (see Appendix X2) and zinc-coated (galvanized) by the hot-dip process in coils and cut lengths.

Note 1—See Appendix X2 for a description of the Twin-Roll Cast process.

1.2 The product is produced in various zinc coating weights [masses] or coating designations as shown in Table 1.

1.3 Product furnished under this specification shall conform to the applicable requirements of the latest issue of Specification A924/A924M unless otherwise provided herein.

1.4 The product is available in a number of designations, grades and classes and in the two following general categories that are designed to be compatible with different application requirements.

1.4.1 Steels with mandatory chemical requirements and typical mechanical properties.

1.4.2 Steels with mandatory chemical requirements and mandatory mechanical properties.

1.5 This material is available in the following sizes:

1.5.1 Thicknessup to 0.078 in. [2.0 mm]

1.5.2 Widthup to 79 in. [2000 mm]

1.6 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification.

1.7 This specification is applicable to orders in either inch-pound units (as A1063) or SI units (as A1063M). Values in inch-pound and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independently of the other.

1.8 Unless the order specifies the M designation (SI units), the product shall be furnished to inch-pound units.

1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

TABLE 1 Weight [Mass] of Coating RequirementsA, B, C

Note— Use the information provided in 8.1.2 to obtain the approximate coating thickness from the coating weight [mass].

Minimum Requirement
Triple-Spot Test
Single-Spot Test
Inch-Pound Units
TypeCoating DesignationTotal Both Sides, oz/ft2
One Side, oz/ft2
Total Both Sides, oz/ft2
ZincG01C no minimumno minimum no minimum
G30 0.300.100.25
G40 0.400.120.30
G60 0.600.200.50
G90 0.900.320.80
G1001.000.360.90
G1151.150.401.00
G1401.400.481.20
G1651.650.561.40
G1851.850.641.60
SI Units
TypeCoating Designation
Total Both Sides, g/m2
One Side, g/m2
Total Both Sides, g/m2
ZincZ001C no minimumno minimumno minimum
Z90 90 30 75
Z120 120 36 90
Z180 180 60150
Z275 275 94235
Z305 305110275
Z350 350120300
Z450 450154385
Z500 500170425
Z550 550190475
Z600 600204510

A The coating designation number is the term by which this product is specified. Because of the many variables and changing conditions that are characteristic of continuous hot-dip coating lines, the zinc coating is not always evenly divided between the two surfaces of a coated sheet; nor is it always evenly distributed from edge to edge. However, the minimum triple-spot average coating weight (mass) on any one side shall not be less than 40 % of the single-spot requirement.

B As it is an established fact that the atmospheric corrosion resistance of zinc coated sheet products is a direct function of coating thickness (weight (mass)), the selection of thinner (lighter) coating designations will result in almost linearly reduced corrosion performance of the coating. For example, heavier galvanized coatings perform adequately in bold atmospheric exposure whereas the lighter coatings are often further coated with paint or a similar barrier coating for increased corrosion resistance. Because of this relationship, products carrying the statement meets ASTM A1063/A1063Mrequirements should also specify the particular coating designation.

C No minimum means that there are no established minimum requirements for triple- and single-spot tests.

Ключевые слова:
alloyed coating; direct cast steel; high strength low alloy; minimized spangle coating; sheet steel; spangle; steel; steel sheet; structural steel; zinc; zinc coated (galvanized); zinc iron-alloy; zinc iron-alloy coated: Hot-dip processed coatings; Steel sheet; Twin-roll casting; Zinc-coated steel sheet