(812) 309-78-59
(495) 223-46-76
ASTM A381-96(2012)
Standard Specification for Metal-Arc-Welded Steel Pipe for Use With High-Pressure Transmission Systems
5 стр.
Заменен
Электронный (pdf)Печатное издание
96.72 $ (включая НДС 20%)
Разработчик:
Зарубежные/ASTM
ICS:
23.040.10 Iron and steel pipes / Чугунные и стальные трубы
Сборник (ASTM):
01.01 Steel--Piping, Tubing, Fittings / Сталь - Система трубопроводов, Трубы, Фитинги
Тематика:
Steel--Structural, Tubes, Plate, Coated
Описание
Реферат

This specification covers metal-arc-welded steel pipe for use with high pressure transmission systems. The pipe is intended for fabrication of fittings and accessories for compressor or pump-station piping. The required chemical compositions for carbon steel, and the tensile properties of finished pipes are presented. Mechanical testing requirements namely transverse body tension test and transverse weld tension test shall be performed on each length of pipe from each lot of 100 lengths, and transverse guided-bend weld test cut from a length of pipe from each lot of 50 length, also hydrostatic test from each length of pipes shall be performed. A radiographic examination shall also be performed to ensure that the welding equipment is consistently producing the required quality.

Область применения

1.1 This specification covers straight seam, double-submerged-arc-welded steel pipe (Note 1) suitable for high-pressure service, 16 in. (406 mm) and larger in outside diameter, with wall thicknesses from 5/16 to 11/2 in. (7.9 to 38 mm). The pipe is intended for fabrication of fittings and accessories for compressor or pump-station piping. Pipe ordered to this specification shall be suitable for bending, flanging (vastoning), corrugating, and similar operations.

Note 1A comprehensive listing of standardized pipe dimensions is contained in ANSI B36.10.
Note 2The term “double welded” is commonly used in the gas and oil transmission industry, for which this pipe is primarily intended, to indicate welding with at least two weld passes, of which one is on the outside of the pipe and one on the inside. For some sizes of the pipe covered by this specification, it becomes expedient to use manual welding, in which case the provisions of Note 3 shall be followed.

1.2 Nine classes of pipe, based on minimum yield point requirements, are covered as indicated in Table 1.

TABLE 1 Tensile Requirements

Class

Yield Strength,
min, psi (MPa)

Tensile Strength,
min, psi (MPa)

Elongation in 2 in.
(50.8 mm),
min, %

Y 35

35 000 (240)

60 000 (415)

26

Y 42

42 000 (290)

60 000 (415)

25

Y 46

46 000 (316)

63 000 (435)

23

Y 48

48 000 (330)

62 000 (430)

21

Y 50

50 000 (345)

64 000 (440)

21

Y 52

52 000 (360)

66 000 (455)

20

Y 56

56 000 (385)

71 000 (490)

20

Y 60

60 000 (415)

75 000 (515)

20

Y 65

65 000 (450)

77 000 (535)

20


1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 The following caveat applies to the test methods portion, Sections 9 and 10, only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Ключевые слова:
arc welded steel pipe; steel pipe