(812) 309-78-59
(495) 223-46-76
ASTM B122/B122M-08
Standard Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar
7 стр.
Заменен
Печатное изданиеЭлектронный (pdf)
96.72 $ (включая НДС 20%)
Разработчик:
Зарубежные/ASTM
ICS:
77.150.30 Copper products / Продукция из меди
Сборник (ASTM):
02.01 Copper and Copper Alloys / Медь и сплавы из меди
Тематика:
Copper
Описание
Реферат

This specification establishes the requirements for copper-nickel-tin, copper-nickel-zinc, and copper-nickel alloy plates, sheets, strips, and rolled bars made from UNS C70600, C70620, C71000, C71500, C71520, C72200, C72500, C73500, C74000, C74500, C75200, C76200, or C77000 alloy. Each product should be manufactured by hot or cold working, and annealed if required, to produce a uniform wrought structure that meets the specified temper properties. This specification also contains information on the standard tempers for and tensile strengths of hot-rolled, cold-rolled, and annealed tempers. In case of disagreements, the chemical composition is determined following appropriate methods listed here. Grain size is the standard requirement for all products in the annealed tempers.

Область применения

1.1 This specification establishes the requirements for copper-nickel-tin alloy, copper-nickel-zinc alloy (nickel silver), and copper-nickel alloy plate, sheet, strip, and rolled bar. The following alloys are covered:

Previously
Copper AlloyUsed Nominal Composition,
UNS No. Designation%

Copper

Nickel

Zinc

Tin
Chro-
mium
C70600...9010 .........
C70620...8610.........
C7100068020 .........
C7150057030 .........
C71520...6531.........
C72200...8515 ......0.5
C72500...89 9 ...2...
C7350017218 10......
C7400097010 20......
C7450036510 24......
C7520026518 17......
C7620085912 29......
C7700045518 27......

Note 1—Plates of copper-nickel alloy Copper Alloy UNS Nos. C70600, C70620, C71500, C71520, and C72200 for use as tube plates in surface condensers and heat exchangers are covered by Specification B 171/B 171M.

1.2 The values stated in either inch-pound units of SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

1.2.1 When the product is ordered in inch-pound units, the inch-pound units are to be regarded as the standard except grain size is always specified in millimetres.

1.2.2 When the product is ordered in SI units, the SI units are to be regarded as the standard.

Ключевые слова:
copper-nickel plate; copper-nickel rolled bar; copper-nickel sheet; copper-nickel strip; copper-nickel-tin plate; copper-nickel-tin rolled bar; copper-nickel-tin sheet; copper-nickel-tin strip; copper-nickel-zinc plate; copper-nickel-zinc rolled bar; copper-nickel-zinc sheet; copper-nickel-zinc strip; Copper alloy plate/sheet/strip/rolled bar--specifications; Copper-nickel alloys--specifications; Copper-nickel-tin; Copper-nickel-zinc alloys; Nickel silver alloy--specifications; UNS C70600 (Cu-Ni, 10%); UNS C71000; UNS C71500; UNS C72200 (copper nickel); UNS C72500 (copper nickel); UNS C73500 (nickel silver); UNS C74000 (nickel silver); UNS C74500 (nickel silver); UNS C75200 (nickel silver); UNS C76200 (nickel silver); UNS C77000 (nickel silver)