(812) 309-78-59
(495) 223-46-76
ASTM B249/B249M-15a
Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
14 стр.
Заменен
Печатное изданиеЭлектронный (pdf)
104.52 $ (включая НДС 20%)
Разработчик:
Зарубежные/ASTM
ICS:
77.150.30 Copper products / Продукция из меди
Сборник (ASTM):
02.01 Copper and Copper Alloys / Медь и сплавы из меди
Тематика:
Copper
Описание
Значение и использование

12.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table and for dimensional tolerances, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.

Property

Rounded Unit for Observed or
Calculated Value

 

 

Chemical composition

 

Hardness

nearest unit in the last right-hand

Electrical resistivity

significant digit used in expressing the

Electrical conductivity

limiting value

 

 

Tensile strength

nearest ksi [5 MPa]

Yield strength

 

 

 

Elongation:

nearest 1 %

 

 

Grain size:

 

 Under 0.060 mm

nearest multiple of 0.005 mm

 0.060 mm and over

nearest 0.01 mm

Реферат

This specification establishes the general requirements common to wrought copper and copper alloy rods, bars, shapes, and forgings. Products shall be manufactured by hot working, cold working, or both, and finished by cold working, annealing, or heat treatment and straightening as identified necessary to meet the properties specified. Materials shall be sampled and prepared, then tested accordingly to examine their conformance to dimensional (mass, diameter, length, straightness, and edge contours), mechanical (tensile strength, Rockwell hardness, elongation, and hydrogen embrittlement), electrical resistivity, chemical composition, and grain size requirements. The products shall also meet performance requirements when subjected to residual stress, mercurous nitrate, ammonia vapor, and semiguided bend tests. In the event of conflict between this specification and the individual casting product specifications, the requirements of the casting specification shall take precedence.

Область применения

1.1 This specification2 establishes the general requirements common to wrought copper and copper alloy rod, bar, shapes, and forgings which shall apply to Specifications B16/B16M, B21/B21M, B98/B98M, B124/B124M, B138/B138M, B139/B139M, B140/B140M, B150/B150M, B151/B151M, B187/B187M, B196/B196M, B283/B283M, B301/B301M, B371/B371M, B411/B411M, B441, B453/B453M, B455, B570, B870, B927/B927M, B929, B967/B967M, and B974/B974M to the extent referenced therein.

1.2 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification are prescribed in the product specification.

1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3.1 Within the text the SI values are given in brackets.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Ключевые слова:
bar, general requirements; bar, rod, shapes, general requirements; rod, general requirements; shape, general requirements;