(812) 309-78-59
(495) 223-46-76
ASTM C541/C541M-98(2019)
Standard Specification for Linings for Asbestos-Cement Pipe (Withdrawn 2022)
3 стр.
Отменен
Электронный (pdf)Печатное издание
87.36 $ (включая НДС 20%)
Разработчик:
Зарубежные/ASTM
ICS:
23.040.50 Pipes and fittings of other materials / Трубы и фитинги из других материалов
Сборник (ASTM):
04.05 Chemical–Resistant Nonmetallic Materials; Vitrified Clay Pipe; Concrete Pipe; Fiber-Reinforced Cement Products; Mortars and Grouts; Masonry; Precast Concrete / Химически устойчивые неметаллические материалы; Глазированные керамические трубы; Трубы бетонные; изделия из фиброцемента; Известковые цементные растворы; Монолитный бетон; Сборный бетон
Тематика:
Masonry
Описание
Причина отменыThis specification covers requirements for plastic linings to be applied to asbestos-cement pipe, designed for special service in carrying corrosive fluids. This specification also covers methods of testing plastic lining material as well as sections of lined pipe. The requirements established by this specification shall serve as a guide in, but not the sole basis for, judging the suitability of the product for a particular service. The selection of the material should include consideration of performance in similar applications or testing under the intended service condition.

Formerly under the jurisdiction of Committee C17 on Fiber-Reinforced Cement Products, this specification was withdrawn in January 2022. This standard is being withdrawn without replacement because there are currently no experts to maintain it.

Реферат

This specification covers requirements for plastic linings to be applied to asbestos-cement pipe, designed for special service in carrying corrosive fluids. This specification also covers methods of testing plastic lining material as well as sections of lined pipe. Thermosetting polymer linings and those thermoplastic linings that do not rely on mechanical means to hold them to the pipe wall shall have a strong permanent bond to the pipe wall. The plastic lining used shall be highly resistant to acids and alkalis, and shall be completely resistant to acids generated by the hydrogen sulfide corrosion cycle. The chemical resistance tests for lined test specimens and lining material are presented in details. Three adhesion tests procedure for the specimens are presented.

Область применения

1.1 This specification covers requirements for plastic linings to be applied to asbestos-cement pipe, designed for special service in carrying corrosive fluids. This specification also covers methods of testing plastic lining material as well as sections of lined pipe. The requirements established by this specification shall serve as a guide in, but not the sole basis for, judging the suitability of the product for a particular service. The selection of the material should include consideration of performance in similar applications or testing under the intended service condition.

Note 1: To determine the suitability of the product for a particular service or corrosive fluid, refer to the manufacturer for specific recommendations.

1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3 Warning—Breathing of asbestos dust is hazardous. Asbestos and asbestos products present demonstrated health risks for users and for those with whom they come into contact. In addition to other precautions, when working with asbestos-cement products, minimize the dust that results. For information on the safe use of chrysotile asbestos, refer to “Safe Use of Chrysotile: A Manual on Preventive and Control Measures.”2

1.4 The following precautionary caveat pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Ключевые слова:
asbestos; asbestos-cement; asbestos-cement pipe; linings; pipe;