(812) 309-78-59
(495) 223-46-76
ASTM D1974/D1974M-16
Standard Practice for Methods of Closing, Sealing, and Reinforcing Fiberboard Boxes
16 стр.
Заменен
Электронный (pdf)Печатное издание
112.32 $ (включая НДС 20%)
Разработчик:
Зарубежные/ASTM
ICS:
55.180.20 General purpose pallets / Поддоны общего назначения
Сборник (ASTM):
15.10 Packaging; Primary Barrier Packaging; Cannabis / Упаковка; Первичная барьерная упаковка; Каннабис
Тематика:
Paper & Packaging
Описание
Значение и использование

4.1 The means of closing the flaps of corrugated shipping containers is one of the important decisions for a shipper. It may affect the overall material cost, the labor costs, the packaging equipment costs, and the performance of the box during distribution.

4.2 This practice provides a list of many available procedures for closing, sealing, and reinforcing boxes. Most of these describe a particular packaging material and a particular use of it on a box. Some methods involve package performance testing; any closure or reinforcement which passes prescribed tests (usually on the proposed box and contents) is considered to comply with that section of this practice. Performance-based methods are encouraged because they allow for considerable flexibility in the choice of packaging materials and methods yet provide assurance of a given level of performance.

4.3 A diverse range of methods are described in this practice but relative performance levels are not given. Laboratory package testing such as Practice D4169 and field experience are recommended to rate alternative methods on performance for the intended use.

4.4 The descriptions of materials and methods in this practice provide direction for the procurement of materials and for their common uses on boxes. These descriptions may be sufficient for some specification purposes, but others will require more thorough material and application requirements than those given here.

4.5 The list of methods in this practice is not exhaustive; deviation or variation from the listed methods is possible with the approval of the appropriate parties referencing this practice. Depending on the characteristics of the contents, the specific shipping container, the acceptable package costs, the distribution hazards, and the desired degree of assurance of successful shipment, more stringent methods than those listed may be needed or less stringent methods than those listed may be adequate. The methods described are typical uses of the closure, reinforcing, or sealing materials; many of these materials can be used for other box styles or other methods on boxes but all of these are not included in this practice. Materials for box closure, reinforcement, or sealing are commercially available which have higher or lower performance characteristics than those listed in this practice; these may often be used in a lesser or greater quantity than the described applications of the listed materials.

4.6 This practice assumes the following:

4.6.1 The shipping container and inner packing are properly designed for the contents and the distribution hazards (see Practices D4169 and D5118/D5118M),

4.6.2 Normal, reasonable care is taken in shipment, including storage, handling, loading, and bracing, and

4.6.3 Normal, reasonable care is taken in the application of the closure, reinforcing, or sealing materials to the shipping container.

Область применения

1.1 This practice describes several methods for closing, sealing, and reinforcing fiberboard (solid and corrugated, excluding triple wall) shipping boxes used for shipment. One or several methods listed in this practice may be referenced in regulations, specifications, or contracts. (See Appendix for cross reference).

1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Note 1: This practice is intended to be workable in both inch-pound units and SI units. Unit conversions are intended to be functional but are not necessarily exact; this should not significantly affect the performance of the closing, sealing, or reinforcing methods. Descriptions in inch-pound and SI units are considered interchangeable in this practice.

Note 2: All references to this standard should be made by closure number.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Ключевые слова:
box; close; closure; fiberboard; package; reinforcement; seal;