(812) 309-78-59
(495) 223-46-76
ASTM D5579-15
Standard Test Method for Evaluating the Thermal Stability of Manual Transmission Lubricants in a Cyclic Durability Test
19 стр.
Заменен
Электронный (pdf)Печатное издание
104.52 $ (включая НДС 20%)
Разработчик:
Зарубежные/ASTM
ICS:
75.100 Lubricants,. Including mineral oils, fluids for metal working and for temporary protection against corrosion / Смазки, индустриальные масла и связанные с ними продукты. Включая минеральные масла, жидкости для обработки металлов и для временной защиты от коррозии
Сборник (ASTM):
05.02 Petroleum Products, Liquid Fuels, and Lubricants (II): D3711–D6122 / Нефтепродукты, жидкое топливо и смазочные материалы (II): D3711–D6122
Тематика:
Petroleum
Описание
Значение и использование

5.1 This test method is used to evaluate automotive manual transmission fluids for thermal instability, which results in deterioration of synchronizer performance.

5.2 This test method may also be utilized in other specifications and classifications of transmission and gear lubricants such as the following:

5.2.1 (final API designation of PG-1),

5.2.2 Military Specification MIL-L-2105,

5.2.3 SAE Information Report J308 Axle and Manual Transmission Lubricants, and

5.2.4 Mack Truck GO-H Gear Lubricant Specification.

Область применения

1.1 This test method covers the thermal stability of fluids for use in heavy duty manual transmissions when operated at high temperatures.

1.2 The lubricant performance is measured by the number of shifting cycles that can be performed without failure of synchronization when the transmission is operated while continuously cycling between high and low range.

1.3 Correlation of test results with truck transmission service has not been established. However, the procedure has been shown to appropriately separate two transmission lubricants, which have shown satisfactory and unsatisfactory field performance in the trucks of one manufacturer.

1.4 Changes in this test method may be necessary due to refinements in the procedure, obsolescence of parts, or reagents, and so forth. These changes will be incorporated by Information Letters issued by the ASTM Test Monitoring Center (TMC).2 The test method will be revised to show the content of all the letters, as issued.

1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5.1 Exception—When materials, products, or equipment are available only in inch-pound units, SI units are omitted.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.7 This test method is arranged as follows:

 

Section

Scope

1

Referenced Documents

2

Terminology

3

Summary of Test Method

4

Significance and Use

5

Apparatus

6

 Test Transmission

6.2

 Transmission Mounts

6.3

 Oil-Circulating System

6.4

 Oil Return Hole

6.5

 Air Pressure Controls

6.6

 Drive System

6.7

 Instrumentation

6.8

 Thermocouple Placement

6.9

Reagents and Materials

7

Safety

8

Preparation of Apparatus

9

 Cleaning of Parts

9.1

 Assembly

9.2

Calibration

10

 Transmission and Test Stand Calibration

10.1

 Reference Oils

10.2

 Reference Oil Test Frequency

10.3

 Instrumentation Calibration

10.4

 Shift Time Calibration

10.5

Operating Procedure

11

 System Flush and Charge

11.1

 Test Operation

11.2

 Shut-Down Procedure

11.3

 Transmission Disassembly

11.4

Determination of Test Results

12

 Failure Criteria

12.1

 Shifter Fork Wear

12.2

 Test Validity Determination

12.3

Report

13

Precision and Bias

14

Keywords

15

Test Validity Calculations and Limits

Annex A5

HTCT Test Report Forms and Data Dictionary

Annex A6

Manual Transmission Cyclic Durability Test Parts Inspection and Wear Measurements

Annex A7

Ключевые слова:
cyclic transmission test; forkwear; manual transmission lubricants; shifting synchronization; shift time; thermal stability; total cycle time;