(812) 309-78-59
(495) 223-46-76
ASTM E3068-20
Standard Test Method for Contact Measurement of Backface Deformation in Clay Backing During Body Armor Testing
5 стр.
Действует
Печатное изданиеЭлектронный (pdf)
78.00 $ (включая НДС 20%)
Разработчик:
Зарубежные/ASTM
ICS:
13.340.01 Protective equipment in general / Защитные средства в целом. , 13.310 Protection. Including security services, security procedures, burglar alarm devices, burglary resisting materials and equipment, bullet resisting materials and equipment, anti-theft devices for vehicles, safes, strong rooms, etc. / Защита от преступлений. Включая услуги по обеспечению безопасности, процедуры обеспечения безопасности, устройства тревожной сигнализации против взлома, материалы и оборудование для защиты от взлома, пуленепробиваемые материалы и оборудование, противоугонные устройства для транспортных средств, сейфы, комнаты-сейфы и т.д.
Сборник (ASTM):
15.08 Security Systems and Equipment; Detention and Correctional Facilities; Homeland Security Applications; Driverless Automatic Guided Industrial Vehicles; Exoskeletons and Exosuits / Оборудование и системы безопасности; Исправительные заведения и тюрьмы; Системы национальной безопасности; Беспилотный автоматически управляемый промышленный транспорт; Экзоскелеты и экзокостюмы
Тематика:
Consumer Products
Описание
Значение и использование

5.1 U.S. Department of Defense and U.S. Department of Justice standards for assessing the performance of ballistic-resistant torso body armor require the measurement of BFD on backing assemblies made with ROMA Plastilina No. 1®6.

5.2 This test method may be applicable for certification testing or for research and development testing.

Область применения

1.1 This test method describes test methods for the contact measurement of backface deformation (BFD) in clay backing caused by a test threat that produces a partial penetration in a body armor test item.

1.2 This test method is applicable to testing of planar and nonplanar soft armor and hard armor.

1.3 This test method is not applicable to testing of helmets.

1.4 The purpose of this test method is to achieve consistent measurements between laboratories and reduce differences that could result from using different measurement techniques.

1.5 It is anticipated that this test method will be referenced by certifiers, purchasers, and other users in order to meet their specific needs.

1.6 This test method does not specify BFD performance requirements for body armor. The performance requirements are included in other standards or specifications. The decision rules for determining conformance to specifications and the consideration of uncertainty are also included in other standards or specifications.

1.6.1 In this test method, “other standards and specifications” and “unless specified elsewhere” refer to documents (for example, military standards, purchase specifications) that require the use of this test method. Certifiers, purchasers, and other users are responsible for the “other standards and specifications” and for specifying any requirements that supersede those of this test method.

1.7 Units—The values stated in SI units are to be regarded as standard. Where appropriate, mathematical conversions to non-SI units are provided in parentheses for informational purposes.

1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Ключевые слова:
backface deformation; back face deformation; body armor; backing material; ballistic-resistant;