(812) 309-78-59
(495) 223-46-76
ASTM E712-80(2009)
Standard Practice for Laboratory Screening of Metallic Containment Materials for Use With Liquids in Solar Heating and Cooling Systems (Withdrawn 2018)
8 стр.
Отменен
Печатное изданиеЭлектронный (pdf)
96.72 $ (включая НДС 20%)
Разработчик:
Зарубежные/ASTM
ICS:
77.040.99 Other methods of testing of metals / Методы испытания металлов прочие
Сборник (ASTM):
12.02 Nuclear (II), Solar, and Geothermal Energy; Radiation Processing / Ядерная энергия (II), Солнечная, и Геотермическая Энергия; Радиационная обработка
Тематика:
Nuclear Technology
Описание
Причина отменыThis practice covers several laboratory test procedures for evaluating corrosion performance of metallic containment materials under conditions similar to those that may occur in solar heating and cooling systems.

Formerly under the jurisdiction of Committee E44 on Solar, Geothermal and Other Alternative Energy Sources, this practice was withdrawn in July 2018 in accordance with section 10.6.3 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

Значение и использование

At this time, none of these tests has been demonstrated to correlate with field service.

It is essential that consideration be given to the appropriate pairing of metal and fluid since these procedures do not restrict the selection of either the containment material or the fluid for testing. Likewise, knowledge of the corrosion protection mechanism and the probable mode of failure of a particular metal is helpful in the selection of test conditions and the observation, interpretation, and reporting of test results.

The design of solar heating and cooling systems strongly affects the applicability of the results of the laboratory screening tests. Therefore, the results of these laboratory procedures should be confirmed by component and systems testing under actual or simulated service conditions.

Table 1 is provided to assist in an orderly consideration of the important factors in testing. It is expected that the user of the test procedure will investigate a range of test times and temperatures for the containment material in a metal/fluid pair, and adjust the time and temperature of testing as necessary.

Note 1—Corrosion, whether general or localized, is a time-dependent phenomenon. This time dependence can show substantial nonlinearity. For example, formation of a protective oxide will diminish corrosion with time, while certain forms of localized attack accelerate with time. The minimum time required for a test to provide a corrosion rate that can be extrapolated for the prediction of long-term performance varies widely, depending on the selection of metal and fluid, and on the form of corrosion attack. Therefore, it is not possible to establish a single minimum length of test applicable to all materials and conditions. However, it is recommended that for the tests described in this practice, a test period of no less than 30 days be used. Furthermore, it is recommended that the effect of time of testing be evaluated to detect any significant time dependence of corrosion attack.

It is essential for the meaningful application of these procedures that the length of the test be adequate to detect changes in the nature of the fluid that might significantly alter the corrosivity of the fluid. For example, exhaustion of chemical inhibitor or chemical breakdown of the fluid may occur after periods of months in selected cycles of operation.

Note 2—Many fluids that may be considered for solar applications contain additives to minimize the corrosivity of the fluid. Many such additives are useful only within a specific concentration range, and some additives may actually accelerate corrosion if the concentration falls below a critical level. Depletion kinetics can be a strong function of the exposed metal surface area. Therefore, for tests involving fluids with such additives, consideration must be given to the ratio of metal surface area to fluid volume as it may relate to an operating system.

TABLE 1 Significant Variables in Evaluation of Containment Material/Heat Transfer Fluid PairsA

Test AspectVariable
TemperatureFlow Rate
I.Operating Conditions of System:
A. Operating, full flow

B. Stagnant, full
normal operating

fluid boiling point without pressurization or no-flow temperature with pressurization
normal operating

convection
C. Stagnant, partial fill

D. Stagnant, empty
same as stagnant, full

no-flow temperature
convection

not applicable
II.Test Specimen Design A. flat metal couple
B. metal couple with crevice
C. dissimilar metal couple
D. dissimilar metal couple with crevice
III.Fluid TypeA. fluid intended for use in system
B. fluid pretreated by thermal exposure or chemical contamination
IV.Test CycleA. long time, constant temperature
B. cycles of heating, holding, and cooling
C. cycles of operating full flow, and stagnation
D. cycles of wetting and drying

A In this table, the subdivisions are not necessarily related in correspondence to their lettering.

Область применения

1.1 This practice covers several laboratory test procedures for evaluating corrosion performance of metallic containment materials under conditions similar to those that may occur in solar heating and cooling systems. All test results relate to the performance of the metallic containment material only as a part of a metal/fluid pair. Performance in these laboratory test procedures, taken by itself, does not necessarily constitute an adequate basis for acceptance or rejection of a particular metal/fluid pair in solar heating and cooling systems, either in general or in a particular design. This practice is not intended to preclude the use of other screening tests, particularly when those tests are designed to more closely simulate field service conditions.

1.2 This practice describes apparatus and procedures for several tests, any one or more of which may be used to evaluate the deterioration of the metallic containment material in a metal/fluid pair. The procedures are designed to permit simulation, heating, and cooling systems including (1) operating full flow, (2) stagnant full, (3) stagnant partial fill, and (4) stagnant empty. Particular attention should be directed to properly reflecting whether the system is open or closed to atmosphere.

1.3 This practice covers the following six tests:

Practice ABasic Immersion Test at Atmospheric Pressure
Practice BHeat-Rejecting Surface Test at Atmospheric Pressure
Practice CHigh-Pressure Test
Practice DRepeated Dip Dry Test at Atmospheric Pressure
Practice ECrevice Test at Atmospheric Pressure
Practice FTube Loop Test at Atmospheric Pressure

1.4 Practice A is concerned with the interaction of metal and fluid when both are at the same temperature with no heat transfer from one to the other. It is regarded as useful for plumbing, pumps, tanking, etc., but of less significance, taken by itself, for collector panels. Practices B and F are concerned with the deterioration of the metal when there is transfer of heat from the metal into the heat transfer fluid. These practices are especially applicable to the collector panel. Practice C permits a variety of tests but is especially useful in relation to systems that experience high temperatures, or are closed to the atmosphere. Practices D and E evaluate specific corrosion problems that may be associated with particular metal/fluid pairs and particular designs of systems and components.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Ключевые слова:
corrosion; deterioration; high pressure; immersion; metallic containment materials; solar collector; solar heating and cooling; Containment systems/applications; Corrosion--metals/alloys; Corrosion--solar devices; Crevice corrosion; Deterioration; Dip test; Electrolytic cleaning; Immersion--solar devices; Pressure testing--solar devices; Solar heating/cooling systems; Transmittance and reflectance--solar devices; Tube loop test