(812) 309-78-59
(495) 223-46-76
ÖNORM EN 1451-1:2000-01
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
Заменен
Печатная копияПечатное издание
126.00 € (включая НДС 20%)
Разработчик:
Зарубежные/ON
ICS:
23.040.20 Plastics pipes / Пластмассовые трубы23.040.45 Plastics fittings / Пластмассовые фитинги91.140.80 Drainage systems / Дренажные системы
Описание
This European Standard specifies the requirements for pipes, fittings and the system of polypropylene (PP) solid-wall piping systems in the field of soil and waste discharge (low and high temperature) inside buildings (marked with "8") and for soil and waste discharge systems for both inside buildings and buried in ground within the building structure (marked with "BD").
NOTE 1 : The application area "inside buildings" according to this standard, applies to the interior area of the building only. The application area "within the building structure" conforms to the requirements for "inside buildings" according to prEN 12056-1.
It also specifies the test parameters for the test methods referred to in this standard. This standard is applicable to PP pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following purposes:
a) soil and waste discharge pipework for the conveyance of domestic waste waters (low and high temperature);
b) ventilation pipework associated with a);
c) rainwater pipework within the building structure.
It applies to pipes and fittings, marked with "E", which are intended to be used inside buildings and outside buildings
fixed onto the wall.
It applies to pipes and fittings, marked with "BD", which are intended to be used for both inside buildings and buried in ground within the building structure,
NOTE 2: Only components marked with "BD" are generally to be used buried in ground within the building structure; these are required to have a nominal ring stiffness of at least SN 4 and a nominal outside diameter equal to or greater than 75 mm.
NOTE 3: Pipes and fittings of the pipe series S 20 are intended to be used for application area "B" only.
This standard is applicable to PP pipes and fittings of the following types: piain-ended; with integral elastomeric ring seal socket; for butt fusion joints; whereby t (...abbreviated)
In dieser ÖNORM werden die allgemeinen Aspekte von Rohrleitungssystemen aus Polypropylen (PP) für Abwasserleitungen niederer und hoher Temperatur innerhalb von Gebäuden sowie für Abwasserleitungen innerhalb von Gebäuden erdverlegt und innerhalb der Gebäudestruktur festgelegt. Diese ÖNORM ist mit einem der Teile 2, 3 und 5 auf Rohre und Formstücke aus PP, deren Verbindungen und auf Verbindungen mit Bauteilen aus anderen Kunststoffen für die folgenden Verwendungszwecke anwendbar: a) Abwasserleitungen für die Ableitungen häuslichen Abwassers niederer und hoher Temperatur; b) Entlüftungseinrichtungen in Verbindungen mit o.a. Abwasserleitungen; c) Regenwasserleitungen innerhalb von Gebäuden.
Ключевые слова:
Kunststoff,Kunststoffrohr,Rohr,Rohrleitung,Rohrleitungssystem,Abwasser,Abwasserableitung,Gebäude,Polypropylen,PP,Formstück,Thermoplast,Begriffe,Terminologie,Abbildung,Werkstoff,Abmessung,geometrische Eigenschaft,mechanische Eigenschaft,Gebrauchstauglichkeit,Dichtring,Kennzeichnung,Normkennzeichnung,Normkonformität,Bauwesen