(812) 309-78-59
(495) 223-46-76
ÖNORM EN ISO 5167-2:2003-12
Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 2: Orifice plates (ISO 5167-2:2003)
Действует
Печатная копияПечатное издание
255.53 € (включая НДС 20%)
Разработчик:
Зарубежные/ON
ICS:
17.120.10 Flow in closed conduits / Поток в закрытых каналах
Описание
This part of ISO 5167 specifies the geometry and method of use (installation and operating conditions) of
orifice plates when they are inserted in a conduit running full to determine the flowrate of the fluid flowing in
the conduit.
This part of ISO 5167 also provides background information for calculating the flowrate and is applicable in
conjunction with the requirements given in ISO 5167-1.
This part of ISO 5167 is applicable to primary devices having an orifice plate used with flange pressure
tappings, or with corner pressure tappings, or with D and D/2 pressure tappings. Other pressure tappings
such as vena contracta and pipe tappings have been used with orifice plates but are not covered by this part
of ISO 5167. This part of ISO 5167 is applicable only to a flow which remains subsonic throughout the
measuring section and where the fluid can be considered as single phase. It is not applicable to the
measurement of pulsating flow. It does not cover the use of orifice plates in pipe sizes less than 50 mm or
more than 1 000 mm, or for pipe Reynolds numbers below 5 000.
Dieser Teil von ISO 5167 legt die geometrischen Formen und Maße sowie die Anwendung (Einbau- und
Betriebsbedingungen) von Blenden, die in einer voll durchströmten Rohrleitung zur Bestimmung des Durchflusses
eingebaut sind, fest.
Dieser Teil von ISO 5167 enthält grundlegende Informationen für die Durchflussberechnung und ist gemeinsam mit
den in ISO 5167-1 festgelegten Anforderungen anzuwenden.
Das in diesem Teil von ISO 5167 behandelte Primärgerät ist eine Blende mit Flansch-Druckentnahmen, Eck-
Druckentnahmen oder D- und D/2-Druckentnahmen. Andere Druckentnahmen, wie z. B. Vena-Contracta- und
beliebige Druckentnahmen im Rohr, werden im Zusammenhang mit Blenden zwar verwendet, sind jedoch nicht
1) Siehe ISO 2186:1973 Durchfluss von Fluiden in geschlossenen Leitungen; Anschlüsse zur Drucksignalübertragung
zwischen Primär- und Sekundärelementen.
2) Blenden mit Vena-Contracta-Druckentnahmen werden in diesem Teil von ISO 5167 nicht behandelt.
3) ISA ist die Abkürzung für International Federation of the National Standardizing Associations, den Vorgänger der ISO vor
1946.
4) In den USA wird das klassische Venturirohr vielfach Herschel Venturi tube genannt.
EN ISO 5167-2:2003 (D) 5
Gegenstand dieser Norm. Dieser Teil von ISO 5167 gilt nur für eine Strömung, die im gesamten Messquerschnitt
im Unterschallbereich liegt und wo das Fluid als einphasig betrachtet werden kann. Dieser Teil von ISO 5167 gilt
nicht für Messungen bei pulsierenden Strömungen, für Rohrdurchmesser kleiner als 50 mm oder größer als
1 000 mm und für (rohrbezogene) Reynolds-Zahlen unter 5 000.
Ключевые слова:
Verfahrenstechnik, Messung, Durchfluss, Durchflussmessung, Fluid, Drosselgerät, Leitung, Kreisquerschnitt, Einbaubedingung, Betriebsbedingung, Blende, Rohrleitung, Druckentnahme, Messverfahren, Berechnung, Abbildung, Durchflussberechnung, Expansionszahl, Tabelle