(812) 309-78-59
(495) 223-46-76
ÖNORM EN ISO 5167-3:2003-12
Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles (ISO 5167-3:2003)
Заменен
Печатная копияПечатное издание
196.07 € (включая НДС 20%)
Разработчик:
Зарубежные/ON
ICS:
17.120.10 Flow in closed conduits / Поток в закрытых каналах
Описание
This part of ISO 5167 specifies the geometry and method of use (installation and operating conditions) of
nozzles and Venturi nozzles when they are inserted in a conduit running full to determine the flowrate of the
fluid flowing in the conduit.
This part of ISO 5167 also provides background information for calculating the flowrate and is applicable in
conjunction with the requirements given in ISO 5167-1.
This part of ISO 5167 is applicable to nozzles and Venturi nozzles in which the flow remains subsonic
throughout the measuring section and where the fluid can be considered as single-phase. In addition, each of
the devices can only be used within specified limits of pipe size and Reynolds number. It is not applicable to
the measurement of pulsating flow. It does not cover the use of nozzles and Venturi nozzles in pipe sizes less
than 50 mm or more than 630 mm, or where the pipe Reynolds numbers are below 10 000.
This part of ISO 5167 deals with
a) two types of standard nozzles:
1) the ISA5) 1932 nozzle;
2) the long radius nozzle6);
b) the Venturi nozzle.
The two types of standard nozzle are fundamentally different and are described separately in this part of
ISO 5167. The Venturi nozzle has the same upstream face as the ISA 1932 nozzle, but has a divergent
section and, therefore, a different location for the downstream pressure tappings, and is described separately.
This design has a lower pressure loss than a similar nozzle. For both of these nozzles and for the Venturi
nozzle direct calibration experiments have been made, sufficient in number, spread and quality to enable
coherent systems of application to be based on their results and coefficients to be given with certain
predictable limits of uncertainty.
Dieser Teil von ISO 5167 legt die geometrischen Formen und Maße sowie die Anwendung (Einbau- und
Betriebsbedingungen) von Düsen und Venturidüsen, die in einer voll durchströmten Rohrleitung zur Bestimmung
des Durchflusses eingebaut sind, fest.
Dieser Teil von ISO 5167 enthält grundlegende Informationen für die Durchflussberechnung und ist gemeinsam mit
den in ISO 5167-1 festgelegten Anforderungen anzuwenden.
Dieser Teil von ISO 5167 gilt nur für Düsen und Venturidüsen, in denen die Strömung im gesamten
Messquerschnitt im Unterschallbereich liegt und wo das Fluid als einphasig betrachtet werden kann. Weiterhin
kann jedes Gerät nur innerhalb festgelegter Grenzen für Rohrdurchmesser, Rohrrauheit, Durchmesserverhältnis
und Reynolds-Zahl verwendet werden. Dieser Teil von ISO 5167 gilt nicht für Messungen bei pulsierenden
Strömungen, für Rohrdurchmesser kleiner als 50 mm oder größer als 630 mm und für Reynolds-Zahlen unter
10 000.
Dieser Teil von ISO 5167 behandelt
a) zwei Arten von Norm-Düsen:
1) die ISA-1932-Düse5);
2) die Langradius-Düse6);
b) die Venturidüse.
1) Siehe ISO 2186:1973 ?Durchfluss von Fluiden in geschlossenen Leitungen; Anschlüsse zur Drucksignalübertragung
zwischen Primär- und Sekundärelementen?.
2) Blenden mit Vena-Contracta-Druckentnahmen werden in diesem Teil von ISO 5167 nicht behandelt.
3) ISA ist die Abkürzung für ?International Federation of the National Standardizing Associations?, den Vorgänger der ISO vor
1946.
4) In den USA wird das klassische Venturirohr vielfach ?Herschel Venturi tube? genannt.
5) ISA ist die Abkürzung für ?International Federation of the National Standardizing Assosiations?, welche 1946 durch ISO
ersetzt wurde.
6) Die Langradius-Düse weicht von der ISA-1932-Düse durch Form und Lage der Druckentnahmen ab.
EN ISO 5167-3:2003 (D)
5
Die zwei Arten von Norm-Düsen sind grundsätzlich verschieden und sind in diesem Teil von ISO 5167 getrennt
behandelt. Di (...abgekuerzt)
Ключевые слова:
Verfahrenstechnik, Messung, Durchfluss, Durchflussmessung, Fluid, Drosselgerät, Leitung, Kreisquerschnitt, Einbaubedingung, Betriebsbedingung, Düse, Venturidüse, Form, Abmessung, Anwendung, Berechnung, Abbildung, Expansionszahl, Tabelle