(812) 309-78-59
(495) 223-46-76
ASTM C505M-15
Standard Specification for Nonreinforced Concrete Irrigation Pipe With Rubber Gasket Joints (Metric)
5 стр.
Заменен
Печатное изданиеЭлектронный (pdf)
93.60 $ (включая НДС 20%)
Разработчик:
Зарубежные/ASTM
ICS:
23.040.50 Pipes and fittings of other materials / Трубы и фитинги из других материалов
Сборник (ASTM):
04.05 Chemical–Resistant Nonmetallic Materials; Vitrified Clay Pipe; Concrete Pipe; Fiber-Reinforced Cement Products; Mortars and Grouts; Masonry; Precast Concrete / Химически устойчивые неметаллические материалы; Глазированные керамические трубы; Трубы бетонные; изделия из фиброцемента; Известковые цементные растворы; Монолитный бетон; Сборный бетон
Тематика:
Masonry
Описание
Реферат

This specification covers reinforced concrete pipe with rubber gasket joints to be used for the conveyance of irrigation water with working pressures, including hydraulic transients. The acceptability of the pipe, joint design, and gaskets shall be determined by the results of the tests prescribed in this specification, if and when required, and by inspection to determine whether the pipe and gaskets conform to the specification as to design and freedom from defects. Pipe manufactured in accordance with this specification shall consist of concrete, cement, fly ash, ground granulated blast furnace slag, allowable combinations of cementitious materials, a combination of Portland cement, admixtures and blends, and aggregates. The rubber compound used in the manufacture of the gasket shall be compounded from natural rubber, synthetic rubber, or a mixture of the two fabricated as prescribed in the specification. The rubber from which the gaskets are fabricated shall have the following physical properties: ultimate elongation at break; ultimate elongation at break after aging; hardness; compression set; water absorption; and ozone resistance. If a splice is used in the manufacture of the gasket, the strength shall be such that the gasket shall withstand elongation over the part of the gasket that includes the splice with no visible separation of the splice. Test specimens shall have the following test requirements: number and type of tests; external load test requirement; and hydrostatic test requirement. Rubber gasket compound tests shall include the following: tensile strength; elongation; aging; hardness; compression set; water absorption; and ozone resistance.

Область применения

1.1 This specification covers nonreinforced concrete pipe with rubber gasket joints to be used for the conveyance of irrigation water with working pressures, including hydraulic transients, as shown in Table 1.

(A) Thinner walls are not prohibited on pipe units not over 1.22 m in length but the thickness of such walls should be not less than the internal diameter divided by 10.
(B) With the exception of 525 and 600-mm pipe, higher working pressures are not prohibited to be used up to a maximum of 15 m for 150 through 300-mm diameters and 12 m for 375 through 450-mm diameters. In these cases the strength of the pipe shall be increased to give minimum internal hydrostatic test pressures of at least three times the design working pressure when tested as specified in 10.4.
(C) For hydrostatic test requirements, refer to 10.4.

1.2 This specification is the SI counterpart of Specification C505.

Note 1: This specification is for manufacturing and purchase only and does not include requirements for bedding, backfill, installation, or field repairs. The owner is cautioned that he must correlate field conditions with the characteristics of the pipe specified and provide inspection during installation.

Ключевые слова:
absorption; acceptance criteria; concrete; design; drainage; gasket tests; gaskets; hydrostatic; irrigation; joints; manufacture; nonreinforced; pipe; pressure; rubber gaskets; tests; three-edge bearing;