Каталог стандартов

+7 (495) 223-46-76 +7 (812) 309-78-59
inform@normdocs.ru

ASTM A568/A568M-19a

Действует
Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for — 30 стр.
Реферат

This specification covers the general requirements for carbon, structural, and high-strength, low alloy steel sheets in coils and cut lengths. The steel sheets shall be manufactured by hot-rolling, cold-rolling or temper rolling. Cold-rolled sheets shall undergo annealing after being cold reduced to thickness. Products shall undergo cast or heat analysis, product, check, or verification analysis, and sampling. Product analyses shall be performed wherein specimens shall conform to required chemical composition of carbon, manganese, phosphorus, sulfur, silicon, copper, nickel, chromium, molybdenum, vanadium, columbium, niobium, titanium, aluminum, and nitrogen. Mechanical properties of the materials shall conform to the following properties: tensile strength, yield strength, and bending strength. Thickness, length, width and flatness tolerances and allowances for cold-rolled and hot-rolled sheets are indicated. Steel may be produced as ingot-cast or strand-cast.

Область применения

1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A414/A414M, A424/A424M, A606/A606M, A659/A659M, A794/A794M, A1008/A1008M, A1011/A1011M, and A1039/A1039M.

1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A635/A635M).

1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification.

1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, measured values, calculated values, or observed values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29.

1.4.1 Ordered values, identified in tables, specified such as over 30 through 48 or 30 exclusive to 48 inclusive, covers all ordered values specified as 30.1, 30.01, 30.001, etc., up to and including 48.000 etc., but does not cover ordered values specified as 30.000 etc., or less, nor does it cover ordered values specified as 48.1, 48.01, 48.001, etc.

1.5 Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the “M” specification is used.

Note 1: The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass.

1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.

1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ICS
77.140.50 Flat. Including plate, sheet and strip / Стальной листовой прокат и полуфабрикаты. Включая плиты, листы и полосы
Сборник ASTM
01.03 Steel--Plate, Sheet, Strip, Wire; Stainless Steel Bar / Сталь - Плиты, листы, штрипсы, проволока; сортовой прокат из нержавеющей стали