Каталог стандартов
+7 (495) 223-46-76
+7 (812) 309-78-59
inform@normdocs.ru
This specification covers high-silicon iron pipe and pipe fittings intended for corrosion-resistant service for both above- and below-grade construction. The castings shall be true to pattern, reasonable smooth, and free from defects that would make the castings unfit for the use for which they are intended. The material shall conform to the chemical composition requirements specified. All centrifugally cast high-silicon iron pipe shall be supplied in the as-cast condition. All other pipe and fittings shall be supplied in the stress-relieved condition; the stress relieving procedures are presented. Acid-proof joints for hub/plain-end pipe shall require the use of an acid-proof rope packing. No-hub pipe and fittings shall require a special acid resistant mechanical joint coupling. High-silicon iron pipe can be cut with either manual or hydraulic snap cutters. Hydrostatic testing shall be conducted on all castings.
Область применения1.1 This specification covers high-silicon iron pipe and pipe fittings intended for corrosion-resistant service for both above- and below-grade construction.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 Pipe and pipe fittings shall be the no-hub (MJ) or the hub and plain end design.
1.4 Pipe and pipe fittings shall be of the sizes specified in Table 1 and Table 2 and Figs. 1-71 or other sizes that shall be permitted to conform to the requirements given herein.
TABLE 1 Tolerances for High-Silicon Iron Hub/Plain-End Pipe
Note 1: 1 in. = 25.4 mm.
Size, in.
Wall Thickness, in.
ID Tolerance, in.
OD Tolerance, in.
2
±1/32
±1/32
±1/32
3
±1/32
±1/32
±1/32
4
±1/32
±1/32
±1/32
6
±1/32
±1/32
±3/64
8
±1/32
±1/8
±1/8
10
±1/8
±1/8
±1/8
12
±1/8
±1/8
±1/8
15
±1/8
±1/8
±1/8
TABLE 2 Tolerances for High-Silicon Iron Fittings
Note 1: 1 in. = 25.4 mm.
Size, in.
ID Tolerance,
in.
OD Tolerance,
in.
Stop Lug Depth
Tolerance, in.
11/2
±1/16
±1/16
±1/16
11/2 × 11/2
±1/16
±1/16
±1/16
2
±1/16
±1/16
±1/16
2 × 11/2
±1/16
±1/16
±1/16
2 × 2
±1/16
±1/16
±1/16
3
±1/16
±1/16
±1/16
3 × 11/2
±1/16
±1/16
±1/16
3 × 2
±1/16
±1/16
±1/16
3 × 3
±1/16
±1/16
±1/16
4
±1/16
±1/16
±1/16
4 × 11/2
±1/16
±1/16
±1/16
4 × 2
±1/16
±1/16
±1/16
4 × 3
±1/16
±1/16
±1/16
4 × 4
±1/16
±1/16
±1/16
TABLE 3 Chemical Composition
Element
Composition, Weight %
Grade 1
Grade 2
Carbon
0.65–1.10
0.75–1.15
Manganese
1.50 max
1.50 max
Silicon
14.20–14.75
14.20–14.75
Chromium
0.50 max
3.25–5.00
Molybdenum
0.50 max
0.40-0.60
Copper
0.50 max
0.50 max
FIG. 1 No-Hub Pipe (MJ)
Size, in.
J, in.
F, in.
t, in.
11/2
23/16 (2.19)
84
5/16
2
211/16 (2.69)
84
5/16
3
349/64 (3.77)
84
5/16
4
449/64 (4.77)
84
5/16
Note 1: 1 in. = 25.4 mm.
FIG. 2 Quarter Bends
Size, in.
D, in.
ID, in.
OD, in.
Stop Lug
Depth (P), in.
11/2
41/4
11/2
23/16 (2.19)
11/32
2
41/2
2
25/8 (2.62)
11/32
2 × 11/2
43/16 × 41/2
2 × 11/2
25/8 × 23/16
11/32
3
5
3
33/4 (3.75)
11/32
4
51/2
4
43/4 (4.75)
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 3 Sixth Bends
Size, in.
D, in.
ID, in.
OD, in.
Stop Lug
Depth (P), in.
11/2
3
11/2
23/16
11/32
2
31/4
2
25/8
11/32
3
31/2
3
33/4
11/32
4
33/4
4
43/4
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 4 Return Bends
Size,
in.
C,
in.
D,
in.
F,
in.
R,
in.
ID,
in.
OD,
in.
Stop Lug Depth (P), in.
11/2
2
4
43/4
2
2
53/32
511/16
2
23/8
11/2
2
23/16
25/8
11/32
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 5 Double-Branch Quarter Bend
Size,
in.
D,
in.
E,
in.
ID,
in.
OD,
in.
Stop Lug Depth (P), in.
11/2
37/8
33/4
11/2
23/16
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 6 Eight Bends
Size,
in.
D,
in.
ID,
in.
OD,
in.
Stop Lug Depth (P), in.
11/2
21/2
11/2
23/16
11/32
2
23/4
2
25/8
11/32
3
3
3
33/4
11/32
4
31/4
4
43/4
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 7 Sixteenth Bends
Size,
in.
D,
in.
ID,
in.
OD,
in.
Stop Lug Depth (P), in.
11/2
2
11/2
23/16
11/32
2
21/8
2
25/8
11/32
3
21/4
3
33/4
11/32
4
23/8
4
43/4
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 8 Long-Sweep Quarter Bends
FIG. 9 Sanitary Y Branches
Size,
in.
D,
in.
F,
in.
G,
in.
ID,
in
OD,
in.
Stop Lug Depth (P), in.
1/2 × 11/2
45/8
61/2
17/8
11/2 × 11/2
23/16 × 23/16
11/32
2 × 11/2
47/8
61/2
15/8
2 × 11/2
25/8 × 23/16
11/32
2 × 2
45/8
63/8
2
2 × 2
25/8 × 25/8
11/32
3 × 11/2
55/8
61/2
11/4
3 × 11/2
33/4 × 23/16
11/32
3 × 2
57/8
71/8
11/2
3 × 2
33/4 × 25/8
11/32
3 × 3
63/8
85/8
21/4
3 × 3
33/4 × 33/4
11/32
4 × 11/2
65/8
71/2
13/8
4 × 11/2
43/4 × 23/16
11/32
4 × 2
65/8
71/2
13/8
4 × 2
43/4 × 25/8
11/32
4 × 3
71/8
83/4
13/4
4 × 3
43/4 × 33/4
11/32
4 × 4
75/8
101/4
25/8
4 × 4
43/4 × 43/4
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 10 Double-Branch Sanitary Y
Size,
D,
F,
G,
ID,
OD,
Stop Lug
in.
in.
in.
in.
in.
in.
Depth (P), in.
11/2 × 11/2
45/8
61/2
17/8
11/2 × 11/2
23/16 × 23/16
11/32
2 × 11/2
47/8
61/2
15/8
2 × 11/2
25/8 × 23/16
11/32
2 × 2
45/8
63/8
2
2 × 2
25/8 × 25/8
11/32
3 × 11/2
55/8
61/2
11/4
3 × 11/2
33/4 × 23/16
11/32
3 × 2
57/8
71/8
11/2
3 × 2
33/4 × 25/8
11/32
3 × 3
63/8
85/8
21/4
3 × 3
33/4 × 33/4
11/32
4 × 2
65/8
71/2
13/8
4 × 2
43/4 × 25/8
11/32
4 × 3
71/8
83/4
13/4
4 × 3
43/4 × 33/4
11/32
4 × 4
75/8
101/4
25/8
4 × 4
43/4 × 43/4
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 11 Sanitary Combination Y and 1/8
Bend
Size,
in.
D,
in.
E,
in.
F,
in.
G,
in.
ID,
in.
OD,
in.
Stop Lug
Depth
(P), in.
11/2 × 11/2
43/4
53/8
61/2
17/8
1/2 × 11/2
23/16 × 23/16
11/32
2 × 11/2
43/4
53/4
61/2
15/8
2 × 11/2
25/8 × 23/16
11/32
2 × 2
5
57/8
65/8
17/8
2 × 2
25/8 × 25/8
11/32
3 × 11/2
4
51/4
61/2
15/8
3 × 11/2
33/4 × 23/16
11/32
3 × 2
5
61/4
71/8
11/2
3 × 2
33/4 × 25/8
11/32
3 × 3
61/4
7
81/2
21/4
3 × 3
33/4 × 33/4
11/32
4 × 11/2
45/16
61/8
65/8
13/8
4 × 11/2
43/4 × 23/16
11/32
4 × 2
5
63/8
73/8
13/8
4 × 2
43/4 × 25/8
11/32
4 × 3
6
71/4
83/4
13/4
4× 3
43/4 × 33/4
11/32
4 × 4
73/8
8
101/4
25/8
4× 4
43/4 × 43/4
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 12 Double-Branch Sanitary Combination Y and 1/8 Bend
Size,
in.
D,
in.
E,
in.
F,
in.
G,
in.
ID,
in.
OD,
in.
Stop Lug
Depth
(P), in.
11/2 × 11/2
43/4
53/8
61/2
77/8
11/2 × 11/2
23/16 × 23/16
11/32
2 × 11/2
43/4
53/4
61/2
15/8
2 × 11/2
25/8 × 23/16
11/32
2 × 2
5
57/8
65/8
15/8
2 × 2
25/8 × 25/8
11/32
3 × 11/2
41/4
51/4
61/2
15/8
3 × 11/2
33/4 × 23/16
11/32
3 × 2
5
61/4
71/8
11/2
3 × 2
33/4 × 25/8
11/32
3 × 3
61/4
7
81/2
21/4
3 × 3
33/4 × 33/4
11/32
4 × 2
5
63/8
73/8
13/8
4 × 2
43/4 × 25/8
11/32
4 × 3
6
71/4
83/4
13/4
4 × 3
43/4 × 33/4
11/32
4 × 4
73/8
8
101/4
25/8
4 × 4
43/4 × 43/4
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 13 Sanitary T Branches
Size, in.
E, in.
F, in.
G, in.
ID, in.
OD, in.
Stop Lug
Depth (P), in.
11/2 × 11/2
41/4
63/4
41/4
11/2 × 11/2
23/16 × 23/16
11/32
2 × 11/2
41/2
63/4
41/4
2 × 11/2
25/8 × 23/16
11/32
2 × 11/2 × 11/2
41/2
63/4
41/4
2 × 11/2 × 11/2
25/8 × 23/16 × 23/16
11/32
2 × 2
41/2
67/8
41/2
2 × 2
2 5/8 × 25/8
11/32
3 × 11/2
5
63/4
41/4
3 × 11/2
33/4 × 23/16
11/32
3 × 2
5
71/4
41/2
3 × 2
33/4 × 2 5/8
11/32
3 × 3
5
83/8
5
3× 3
33/4 × 33/4
11/32
4 × 11/2
59/16
67/8
47/32
4× 11/2
43/4 × 23/16
11/32
4 × 2
51/2
71/4
41/2
4 × 2
43/4 × 25/8
11/32
4 × 3
51/2
81/4
5
4 × 3
43/4 × 33/4
11/32
4 × 4
51/2
93/8
51/2
4 × 4
43/4 × 43/4
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 14 Double-Branch Sanitary T
Size,
in.
E,
in.
F,
in.
G,
in.
ID,
in.
OD,
in.
Stop Lug
Depth (P), in.
11/2 × 11/2
41/4
63/4
41/4
11/2 × 11/2
23/16 × 23/16
11/32
2 × 11/2
41/2
63/4
41/4
2 × 11/2
25/8 × 23/16
11/32
2 × 2
41/2
67/8
41/2
2 × 2
25/8 × 25/8
11/32
3 × 11/2
5
63/4
41/4
3 ×11/2
33/4 × 23/16
11/32
3 × 2
5
71/4
41/2
3 × 2
33/4 × 25/8
11/32
3 × 3
5
83/8
5
3 × 3
33/4 × 33/4
11/32
4 × 2
51/2
71/4
41/2
4 × 2
43/8 × 25/8
11/32
4 × 3
51/2
81/4
5
4 × 3
43/4 × 33/4
11/32
4 × 4
51/2
93/8
51/2
4 × 4
43/8 × 43/8
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 15 Sanitary Running Traps
Size,
in.
A,
in.
B,
in.
C,
in.
D,
in.
J,
in.
R,
in.
ID,
in.
OD,
in.
Stop Lug
Depth (P), in.
11/2
23/4
15/8
5
10
4
13/4
11/2
23/16
11/32
2
31/2
115/16
51/2
11
4
2
2
25/8
11/32
3
4
25/16
61/2
13
51/2
21/2
3
33/4
11/32
4
41/2
3
71/2
15
61/2
3
4
43/4
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 16 Sanitary P Traps
Size,
in.
A,
in.
B,
in.
C,
in.
D,
in.
J,
in.
R,
in.
ID,
in.
OD,
in.
Stop Lug Depth (P), in.
11/2
33/4
15/8
31/2
63/4
4
13/4
11/2
23/16
11/32
2
4
115/16
4
71/2
4
2
2
25/8
11/32
3
41/2
25/16
5
9
51/2
21/2
3
33/4
11/32
4
5
3
6
101/2
61/2
3
4
43/4
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 17 Swivel Trap P-Style, Short
Size,
in.
C,
in.
D,
in.
E,
in.
F,
in.
G,
in.
H,
in.
ID,
in.
OD,
in.
Stop Lug Depth (P), in.
11/2
2
83/4
93/4
4
41/2
615/16
73/4
57/16
53/4
13/32
13/8
121/2
12
11/2
2
23/16
25/8
11/32
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 18 Swivel Trap P-Style, Long
Size,
in.
CA,
in.
D,
in.
E,
in.
F,
in.
G,
in.
HA,
in.
ID,
in.
OD,
in.
Stop Lug Depth (P), in.
11/2
123/4
4
615/16
57/16
13/32
121/2
11/2
23/16
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 19 Swivel Type-S Style, Long
Size,
in.
C,
in.
F,
in.
G,
in.
H,
in.
ID,
in.
OD,
in.
Stop Lug Depth (P), in.
11/2
2
6
63/8
8
101/2
143/8
12
223/4
175/8
11/2
2
23/16
25/8
11/32
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 20 Centrifugal Drum Trap P Swivel Type
FIG. 21 Centrifugal Drum Trap S Swivel Type
Size,
in.
C,
in.
D,
in.
E,
in.
F,
in.
J,
in.
ID,
in.
OD,
in.
Stop Lug Depth (P), in.
11/2
4
53/32
63/4
123/4
4
11/2
11/8
11/32
11/2
4
1515/32
63/4
123/4
4
11/2
11/8
11/32
2
43/4
511/16
79/16
141/4
43/4
2
2
11/32
Note 1: 1 in. = 25.4 mm.
FIG. 22 Combination Cleanout and Test Tees
Size, in.
B,
in.
E,
in.
F,
in.
G,
in.
2
27/16
33/4
67/8
37/16
3
33/8
411/16
83/8
43/16
4
37/8
57/16
93/8
411/16
Note 1: 1 in. = 25.4 mm.
FIG. 23 Coupling
Size, in.
A, in.
B, in.
11/2
33/8
27/8
2
4
33/8
3
47/16
43/16
4
415/16
53/16
Note 1: 1 in. = 25.4 mm.
FIG. 24 Pipe Plugs
Size, in.
F, in.
1/2
2
2
21/2
3
21/2
4
21/2
Note 1: 1 in. = 25.4 mm.
FIG. 25 Cleanout Plugs
Size, in.
A, in.
D, in.
E, in.
F, in.
11/2
23/16
21/4
15/16
39/16
2
221/32
21/4
15/16
39/16
3
33/4
21/2
13/8
37/8
4
43/4
23/4
17/16
43/16
Note 1: 1 in. = 25.4 mm.
FIG. 26 Adapter/Hub to No-Hub
Size, in.
A, in.
B, in.
E, in.
F, in.
11/2 × 11/2
323/32
21/4
9/16
45/8
11/2 × 2
313/16
221/32
9/16
45/8
11/2 × 3
313/16
313/16
9/16
45/8
11/2 × 4
313/16
413/16
9/16
47/8
2 × 2
45/16
223/32
5/8
51/8
2 × 3
45/16
313/16
5/8
43/4
2 × 4
45/16
413/16
5/8
5
3 × 3
55/16
313/16
11/16
53/8
4 × 4
69/32
47/8
11/16
59/16
Note 1: 1 in. = 25.4 mm.
FIG. 27 Reducers-Increasers
Size, in.
B, in.
F, in.
2 × 11/2
11/2
8
3 × 11/2
11/2
8
3 × 2
11/2
8
4 × 11/2
11/2
8
4 × 2
11/2
8
4 × 3
11/2
8
Note 1: 1 in. = 25.4 mm.
FIG. 28 Sink Outlet
Size, in.
A, in.
B, in.
C, in.
D, in.
E, in.
F, in.
11/2
0 to 2
101/4
17/8
35/16
1/4
23/16
Note 1: 1 in. = 25.4 mm.
FIG. 29 Sink Overflows
A, in.A
B, in.A
C, in.
4
61/8
1
6
81/8
1
8
101/8
1
Note 1: 1 in. = 25.4 mm.
FIG. 30 Threaded Adapters
Type
Size, in.
AD-7
11/2 Outlet to 11/2 MJ
AD-8
11/2 Outlet to 2 MJ
AD-10
2 Outlet to 2 MJ
Note 1: 1 in. = 25.4 mm.
FIG. 31 Trap Cleanout Details
Note 1: 1 in. = 25.4 mm.
FIG. 32 Adapter – No-Hub and Split Flange
Size, in.
A, in.
J, in.
2
53/4
6
3
7
71/2
4
8
9
Note 1: Flange dimensions are 150 lb ANSI standard.
Note 2: 1 in. = 25.4 mm.
FIG. 33 MJ to Lead Adapter
Type
Size, in.
B, in.
C, in.
D, in.
AD-11
AD-12
11/2
2
21/4
223/32
11/2
11/2
125/32
29/32
Note 1: 1 in. = 25.4 mm.
FIG. 34 Floor Drains
Note 1: 1 in. = 25.4 mm.
FIG. 35 Hub and Plain End Pipe
Size, in.
A, in.
B, in.
C, in.
D, in.
E, in.
F, in.
2
49/16
43/16
35/16
21/32
211/16
25/8
3
55/16
53/16
45/16
31/8
325/32
25/8
4
63/8
63/16
55/16
41/8
425/32
25/8
6
817/32
811/32
75/16
515/16
611/16
3
8
111/4
103/4
95/8
81/4
9
3
10
141/4
133/4
121/4
10
111/4
37/8
12
163/4
16
141/2
12
131/4
4
15
201/4
193/4
173/4
15
163/4
41/8
Size, in.
t, in.
Weight, lb
Working
Length, ft
Overall Length
2
5/16
0.31
7
7 ft 25/8 in.
3
5/16
0.31
7
7 ft 25/8 in.
4
5/16
0.31
7
7 ft 25/8 in.
6
13/32
0.40
7
7 ft 3 in.
8
13/32
0.40
7
7 ft 3 in.
10
5/8
0.62
7
7 ft 37/8 in.
12
5/8
0.62
5
5 ft 4 in.
15
7/8
0.75
5
5 ft 41/8 in.
Note 1: 1 in. = 25.4 mm.
FIG. 36 Straight Tees
Size, in.
Weight,
lb
A, in.
B, in.
C, in.
2 × 11/2
11
81/2
17/8
65/8
2 × 2
12
9
2
7
3 × 2
17
9
21/2
613/16
3 × 3
19
10
21/2
71/2
4 × 2
20
9
3
7
4 × 3
221/2
10
3
71/4
4 × 4
26
11
3
8
Note 1: 1 in. = 25.4 mm.
FIG. 37 Sanitary T Branches
Size, in.
Weight, lb
A, in.
B, in.
C, in.
2 × 11/2
11
81/2
31/2
63/4
2 × 2
12
9
31/2
7
3 × 11/2
16
81/2
4
63/4
3 × 2
18
9
4
7
3 × 3
20
10
4
71/2
4 × 11/2
18
81/2
41/2
63/4
4 × 2
19
9
41/2
7
4 × 3
26
10
41/2
71/2
4 × 4
28
11
41/2
8
6 × 2
31
9
51/2
7
6 × 3
33
10
51/2
71/2
6 × 4
35
11
51/2
8
6 × 6
50
13
51/2
9
8 × 4
62
105/8
61/4
8
8 × 6
65
141/2
65/8
101/2
8 × 8
113
19
65/8
131/2
10 × 6
130
141/4
75/8
101/2
10 × 10
180
21
73/4
141/2
12 × 8
187
19
83/4
131/2
Note 1: 1 in. = 25.4 mm.
FIG. 38 Sanitary Y Branches
Size, in.
Weight, lb
A, in.
B, in.
C, in.
2 × 11/2
11
85/8
43/8
43/8
2 × 2
12
9
41/4
43/4
3 × 11/2
16
85/8
51/16
37/8
3 × 2
17
9
5
43/16
3 × 3
21
101/2
51/2
5
4 × 11/2
17
91/8
513/16
37/8
4 × 2
21
9
53/4
311/16
4 × 3
26
101/2
61/4
41/2
4 × 4
30
12
63/4
51/4
6 × 2
28
9
71/8
211/16
6 × 3
35
101/2
75/8
31/2
6 × 4
45
121/4
81/4
41/4
6 × 6
60
143/4
91/8
53/4
8 × 2
60
167/8
9
41/2
8 × 3
63
121/8
9
33/4
8 × 4
65
131/2
10
41/2
8 × 6
79
161/2
11
61/16
8 × 8
117
191/2
121/4
71/4
10 × 4
160
131/2
111/2
31/2
10 × 6
165
165/8
131/2
37/8
10 × 8
170
193/4
143/8
43/8
10 × 10
180
221/2
15
75/8
12 × 4
173
181/4
153/16
41/2
12 × 6
196
181/4
161/2
41/2
12 × 8
200
233/8
151/2
5
12 × 10
275
27
191/2
6
12 × 12
288
251/2
183/8
71/4
15 × 15
455
321/8
223/4
81/8
Note 1: 1 in. = 25.4 mm.
FIG. 39 Double-Branch Sanitary Tee
FIG. 40 Double-Branch Sanitary Y
Size, in.
Weight, lb
A, in.
B, in.
C, in.
2 × 11/2
14
85/8
43/8
43/8
2 × 2
15
9
41/4
43/4
3 × 11/2
19
85/8
51/16
37/8
3 × 2
20
9
5
43/16
3 × 3
28
101/2
51/2
5
4 × 11/2
21
91/8
513/16
37/8
4 × 2
23
9
53/4
311/16
4 × 3
26
101/2
61/4
41/2
4 × 4
33
12
63/4
51/4
6 × 2
31
9
71/8
211/16
6 × 3
46
101/2
75/8
31/2
6 × 4
52
12
81/8
41/4
6 × 6
65
143/4
91/8
53/4
8 × 4
71
131/2
10
101/2
8 × 6
86
161/2
11
61/16
Note 1: 1 in. = 25.4 mm.
FIG. 41 Double-Branch Sanitary Combination Y and 1/8 Bend (T-Y)
Size, in.
Weight,
lb
A, in.
B and B,
in.
C, in.
E, in.
2 × 11/2
15
85/8
91/4
43/8
73/8
2 × 2
17
9
101/2
43/4
81/4
3 × 11/2
17
85/8
101/4
37/8
73/8
3 × 2
22
9
111/2
43/16
83/16
3 × 3
27
101/2
13
5
99/16
4 × 11/2
24
91/8
113/4
37/8
81/8
4 × 2
24
9
121/2
311/16
83/16
4 × 3
28
101/2
14
41/2
99/16
4 × 4
40
12
151/2
51/4
1013/16
6 × 3
45
101/2
16
31/2
99/16
6 × 4
57
12
171/2
41/4
1013/16
6 × 6
83
15
201/2
53/4
137/16
Note 1: 1 in. = 25.4 mm.
FIG. 42 Short-Sweep Quarter Bends
Size, in.
Weight, lb
B, in.
C, in.
2
11
51/4
8
3
20
6
9
4
25
61/2
10
Note 1: 1 in. = 25.4 mm.
FIG. 43 Long-Sweep Quarter Bends
Size,
in.
Weight,
lb
B,
in.
C,
in.
2
14
81/2
12
3
24
9
121/2
4
29
91/2
13
6
47
101/2
14
8
98
111/8
15
Note 1: 1 in. = 25.4 mm.
FIG. 44 Sanitary Combination Y and 1/8 Bend (T-Y)
Size,
in.
Weight,
lb
A,
in.
B,
in.
C,
in.
E,
in.
2 × 11/2
11
85/8
45/8
43/8
73/8
2 × 2
13
9
51/4
43/4
81/4
3 × 11/2
14
85/8
51/8
37/8
73/8
3 × 2
18
9
53/4
43/16
83/16
3 × 3
24
101/2
61/2
5
99/16
4 × 11/2
17
91/8
57/8
37/8
81/8
4 × 2
21
9
61/4
311/16
83/16
4 × 3
23
101/2
7
41/2
99/16
4 × 4
31
12
73/4
51/4
103/16
6 × 2
33
9
71/4
211/16
83/16
6 × 3
37
101/2
8
31/2
99/16
6 × 4
47
12
83/4
41/4
1013/16
6 × 6
63
15
101/4
53/4
137/16
10 × 6
185
163/4
121/2
47/16
43/8
10 × 8
192
213/8
151/8
61/2
181/2
Note 1: 1 in. = 25.4 mm.
FIG. 45 Quarter Bends
Size,
in.
Weight,
lb
B,
in.
C,
in.
2
9
31/2
7
3
16
4
71/2
4
20
41/2
8
6
36
51/2
9
8
54
61/8
10
10
116
85/8
12
12
195
103/8
14
Note 1: 1 in. = 25.4 mm.
FIG. 46 Sixth Bends
Size,
in.
Weight,
lb
B,
in.
C,
in.
2
8
21/4
53/4
3
11
21/2
6
4
15
23/16
65/16
6
27
33/8
67/8
8
71
41/8
9
Note 1: 1 in. = 25.4 mm.
FIG. 47 Eighth Bends
Size,
in.
Weight,
lb
B,
in.
C,
in.
2
7
13/4
51/4
3
13
115/16
57/16
4
16
23/16
511/16
6
25
29/16
61/16
8
46
311/16
813/16
10
95
41/4
91/4
12
132
5
95/8
Note 1: 1 in. = 25.4 mm.
FIG. 48 Sixteenth Bends
Size,
in.
Weight,
lb
B,
in.
C,
in.
2
6
11/8
45/8
3
8
13/16
411/16
4
11
15/16
413/16
6
21
11/2
5
8
44
21/16
71/8
10
80
2
67/8
Note 1: 1 in. = 25.4 mm.
FIG. 49 Sanitary Increasers
Size,
in.
Weight,
lb
A,
in.
2 × 3
9
9
2 × 4
13
9
2 × 6
17
9
3 × 4
17
9
3 × 6
16
9
4 × 6
17
9
4 × 8
33
115/8
6 × 8
50
117/8
8 × 10
85
16
Note 1: 1 in. = 25.4 mm.
FIG. 50 Hub Strainers
Size,
in.
Weight,
lb
2
21/2
3
3
4
5
6
10
8
18
Note 1: 1 in. = 25.4 mm.
FIG. 51 Sanitary Reducers
Size,
in.
Weight,
lb
A, in.
3 × 11/2
6
5
3 × 2
7
5
4 × 11/2
7
5
4 × 2
9
5
4 × 3
11
5
6 × 2
12
5
6 × 3
13
5
6 × 4
14
5
8 × 4
22
6
8 × 6
25
6
10 × 6
39
6
10 × 8
51
6
12 × 6
55
61/2
12 × 8
65
6
12 × 10
83
6
15 × 6
79
6
15 × 12
109
6
Note 1: 1 in. = 25.4 mm.
FIG. 52 Double Hubs
Size,
in.
Weight,
lb
A,
in.
2
61/2
1
3
9
1
4
12
1
6
18
1
8
40
2
10
82
2
Note 1: 1 in. = 25.4 mm.
FIG. 53 Pipe Plugs
Size,
in.
Weight,
lb
2
2
3
3
4
5
6
10
8
17
12
56
Note 1: 1 in. = 25.4 mm.
FIG. 54 Cleanout Plugs
Size,
in.
Weight,
lb
2
31/2
3
61/2
4
11
6
14
8
26
10
39
Note 1: 1 in. = 25.4 mm.
FIG. 55 Adapter – Plain End and Split Flange
Size,
in.
Weight,
lb
A,
in.
J,
in.
2
5
53/4
6
3
11
7
71/2
4
12
8
9
6
22
91/2
11
8
44
103/4
131/2
Note 1: 1 in. = 25.4 mm.
FIG. 56 Adapter – Hub and Split Flange
Size,
in.
Weight,
lb
A,
in.
J,
in.
2
5
21/2
6
3
7
21/2
71/2
4
12
23/4
9
6
16
3
11
8
36
31/2
131/2
Note 1: 1 in. = 25.4 mm.
FIG. 57 Combination Cleanout and Test Tees
Size,
in.
Weight,
lb
A,
in.
B,
in.
C,
i n.
D,
in.
E,
in.
F,
in.
2
12
21/2
9
313/16
35/8
31/16
27/8
3
22
27/8
10
5
45/8
41/4
313/16
4
29
39/16
11
57/16
55/8
41/2
413/16
Note 1: 1 in. = 25.4 mm.
FIG. 58 Insertable Joints
Plate No.
Size,
in.
Weight,
lb
A,
in.
B,
in.
5045
2
11
73/4
61/2
5070
3
17
83/8
73/8
5095
4
21
91/8
77/8
5144
6
37
91/8
77/8
Note 1: 1 in. = 25.4 mm.
FIG. 59 Backwater Valves
Size, in.
3
4
6
8
Note 1: 1 in. = 25.4 mm.
FIG. 60 Sanitary P Traps
Size,
in.
Without
Vent
Weight, lb
Hub
Vent
Weight, lb
A,
in.
B,
in.
C,
in.
D,
in.
E,
in.
G,
in.
H,
in.
Vent,
in.
2
12
16
11
3
61/4
41/2
21/4
313/16
15/8
2
3
25
32
121/2
41/4
61/4
51/2
3
41/2
25/16
3
4
37
45
14
51/2
7
61/2
31/4
53/16
3
4
6
68
80
17
81/2
8
81/2
4
61/2
315/16
4
Note 1: Depth of seal on all traps shall be 21/2 in.
Note 2: 1 in. = 25.4 mm.
FIG. 61 Sanitary S Traps
Size,
in.
Without
Vent,
Weight, lb
Hub
Vent,
Weight, lb
A,
in.
B,
in.
C,
in.
D,
in.
E,
in.
F,
in.
G,
in.
H,
in.
Vent,
in.
2
16
18
91/4
3
8
41/2
33/4
43/4
313/16
15/8
2
3
24
29
101/2
41/4
10
51/2
41/4
61/4
41/2
25/16
3
4
33
39
111/4
51/2
12
61/2
41/4
7
53/16
3
4
6
82
89
14
81/2
16
81/2
5
9
61/2
315/16
4
Note 1: Depth of seal on all traps shall be 21/2 in.
Note 2: 1 in. = 25.4 mm.
FIG. 62 Sanitary Running Traps
Size,
in.
Without
Vent,
Weight, lb
Single
Hub Vent,
Weight, lb
Double
Hub Vent,
Weight, lb
A,
in.
B,
in.
D,
in.
E,
in.
F,
in.
G,
in.
H,
in.
Vent,
in.
2
14
17
22
131/2
21/2
41/2
21/2
51/4
85/16
15/8
2
3
29
36
42
151/2
3
51/2
31/4
61/4
10
25/16
3
4
41
49
57
171/2
31/2
61/2
31/2
71/4
1111/16
3
4
6
78
87
168
211/2
41/2
81/2
41/4
81/4
15
315/16
4
8
162
165
208
267/8
51/2
11
37/8
12
187/16
51/4
6
10
330
334
346
317/8
71/8
13
51/8
16
221/4
611/16
6
Note 1: Single hub vent is located on the inlet side. Depth of seal on 8- and 10-in. traps is 3 in. All others 21/2 in.
Note 2: 1 in. = 25.4 mm.
FIG. 63 Outside Caulk
Plate
No.
Outlet
Size, in.
Weight, lb
1
2, 3, 4 and 6
45
2
2, 3, 4 and 6
45
3
2, 3, 4 and 6
53
4
2, 3, 4 and 6
53
5
2, 3, 4 and 6
41
6
2, 3, 4 and 6
42
7
2, 3, 4 and 6
48
8
2, 3, 4 and 6
49
Note 1: 1 in. = 25.4 mm.
FIG. 64 Outside Caulk with Basin
Plate
No.
Size,
in.
A,
in.
B,
in.
C,
in.
5, 6, 7, 8
2
27/8
31/2
5/16
3
37/8
41/2
5/16
4
47/8
51/2
3/8
6
7
73/4
3/8
Note 1: 1 in. = 25.4 mm.
FIG. 65 Inside Caulk
Note 1: 1 in. = 25.4 mm.
FIG. 66 Floor Drains
Plate
No.
Outlet
Size, in.
Weight, lb
1
3
70
2
4
73
3
2
37
4
2
45
Plate
No.
Size,
in.
A,
in.
B,
in.
C,
in.
D,
in.
E,
in.
F,
in.
1
2
3
4
8
8
9
9
57/8
63/8
11/2
11/2
14
14
141/2
141/2
Note 1: 1 in. = 25.4 mm.
FIG. 67 Method of Installation
FIG. 68 Floor Drain Funnel Attachment
Note 1: 1 in. = 25.4 mm.
FIG. 69 No. 1, 2, 3, 4, and 5 Overflows
Plate
No.
A, in.A
B, in.A
C, in.
1
2
41/8
1
2
4
61/8
1
3
6
81/8
1
4
8
101/8
1
5
0
21/8
1
Note 1: 1 in. = 25.4 mm.
FIG. 70 Sink Outlet
Plate
No.
Size,
in.
A,
in.
B,
in.
C,
in.
D,
in.
E,
in.
1
11/2 or 2
3/4 to 11/4
10
31/2
43/8
1/8
2
11/2 or 2
1 to 2
10
21/2
37/8
7/16
3
11/2 or 2
1 to 2
10
21/2
3
1/4
4
11/2
0 to 2
101/4
35/16
1/4
Note 1: Furnished with flat loose strainer plates.
Note 2: 1 in. = 25.4 mm.
FIG. 71 Detailed Cross Section of Cleanout
Size, in.
Diameter
of Drain, in.
A, in.
Under 6
11/2
23/16
6 and over
21/4
29/16
Note 1: Traps can be supplied without cleanouts, as shown in the figure.
Note 2: 1 in. = 25.4 mm.
1.4.1 Pipe:
1.4.1.1 No-Hub (MJ) (Fig. 1):
Size (in.)
Length (ft)
11/2
7
2
7
3
7
4
7
1.4.1.2 Hub/Plain End (Fig.35):
Size (in.)
Length (ft)
2
7
3
7
4
7
6
7
8
7
10
5
12
5
15
5
1.4.2 Fitting (No-Hub) (MJ):
Figs.
Quarter Bends
2
Sixth Bends
3
Return Bends
4
Double-Branch Quarter Bend
5
Eighth Bends
6
Sixteenth Bends
7
Long-Sweep Quarter Bends
8
Sanitary Y Branches
9
Double-Branch Sanitary Y
10
Sanitary Combination Y and 1/8 Bend
11
Double-Branch Sanitary Combination Y and 1/8 Bend
12
Sanitary T Branches
13
Double Branch Sanitary T
14
Sanitary Running Traps
15
Sanitary P Traps
16
Swivel Trap P-Style, Short
17
Swivel Trap P-Style, Long
18
Swivel Trap S-Style, Long
19
Centrifugal Drum Trap P Swivel Type
20
Centrifugal Drum Trap S Swivel Type
21
Combination Cleanout and Test Tees
22
Coupling
23
Pipe Plugs
24
Cleanout Plugs
25
No-Hub (MJ) Adapter
26
Reducers-Increasers
27
Sink Outlet
28
Sink Overflows
29
Threaded Adapters
30
Trap Cleanout Details
31
No-Hub (MJ) Adapter
32
(MJ) (No-Hub) to Lead Adapter
33
Floor Drains
34
1.4.3 Fitting (Hub/Plain End):
Figs.
Hub Plain End Pipe
35
Straight Tees
36
Sanitary T Branches
37
Sanitary Y Branches
38
Double-Branch Sanitary Tee
39
Double-Branch Sanitary Y
40
Double-Branch Sanitary Combination Y and 1/8 Bend (T-Y)
41
Short-Sweep Quarter Bends
42
Long-Sweep Quarter Bends
43
Sanitary Combination Y and 1/8 Bend (T-Y)
44
Quarter Bends
45
Sixth Bends
46
Eighth Bends
47
Sixteenth Bends
48
Sanitary Increasers
49
Hub Strainers
50
Sanitary Reducers
51
Double Hubs
52
Pipe Plugs
53
Cleanout Plugs
54
Adapter – Plain end to Split Flange
55
Adapter – Hub to-Split Flange
56
Combination Cleanout and Test Tees
57
Insertable Joints
58
Backwater Valves
59
Sanitary P Traps
60
Sanitary S Traps
61
Sanitary Running Traps
62
Floor Drains
63, 64, 65
Floor Drains
66
Floor Drains/Installation – Funnel Attachment
67, 68
Overflow
69
Sink Outlet
70
Detailed Cross Section of Cleanout
71
Chemical Composition
Table 3
Transverse Bend Test Minimum Requirements
Table S1.1
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.