Каталог стандартов
+7 (495) 223-46-76
+7 (812) 309-78-59
inform@normdocs.ru
Formerly under the jurisdiction of Committee B07 on Light Metals and Alloys, this specification was withdrawn in May 2021 and replaced by Specification B209/B209M for Aluminum and Aluminum-Alloy Sheet and Plate.1
Область применения1.1 This specification covers aluminum and aluminum alloy flat sheet, coiled sheet, and plate in the alloys (Note 1) and tempers shown in Tables 2 and 4, and in the following finishes:
(A) Limits are in mass percent maximum unless shown as a range or stated otherwise.(B) Analysis shall be made for the elements for which limits are shown in this table.(C) For purposes of determining conformance to these limits, an observed value or a calculated value attained from analysis shall be rounded to the nearest unit in the last right hand place of figures used in expressing the specified limit, in accordance with the Rounding Method of Practice E29.(D) Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic Others elements. Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered non-conforming. The Total for Other Elements does not include elements shown in the footnotes with specific composition limits.(E) Other Elements—Total shall be the sum of unspecified metallic elements 0.010 % or more, rounded to the second decimal before determining the sum.(F) Vanadium 0.05 max. The total for other elements does not include vanadium.(G) The aluminum content shall be calculated by subtracting from 100.00 % the sum of all metallic elements present in amounts of 0.010 % or more each, rounded to the second decimal before determining the sum.(H) Composition of cladding alloy as applied during the course of manufacture. Samples from finished sheet or plate shall not be required to conform to these limits.(I) Vanadium, 0.05–0.15, zirconium, 0.10–0.25.(J) 0.05–0.25 Zr.(K) Gallium 0.03 max, vanadium 0.05 max.(L) 0.10–0.6 Mn + Cr.(M) In case there is a discrepancy in the values listed in Table 1 with those listed in the “International Alloy Designations and Chemical Composition Limits for Wrought Aluminum and Wrought Aluminum Alloys” (known as the “Teal Sheets”), the composition limits registered with the Aluminum Association and published in the “Teal Sheets” shall be considered the controlling composition. The “Teal Sheets” are available at http://www.aluminum.org/tealsheets. (A) To determine conformance to this specification, each value for tensile strength and for yield strength shall be rounded to the nearest 1 MPa and each value for elongation to the nearest 0.5 %, both in accordance with the Rounding Method of Practice E29.(B) The basis for establishment of mechanical property limits is shown in Annex A1.(C) Elongations in 50 mm apply for thicknesses up through 12.50 mm and in 5× diameter for thicknesses over 12.50 mm.(D) Materials in either of these tempers, (H32 or H22), (H34 or H24), (H36 or H26), (H38 or H28), (H12 or H22), (H14 or H24), (H16 or H26), (H18 or H28), may be supplied at the option of the supplier, unless one is specifically excluded by the contract or purchase order. When ordered as H2X tempers, the maximum tensile strength and minimum yield strength do not apply. When H2X tempers are supplied instead of ordered H1X or H3X tempers, the supplied H2X temper material shall meet the respective H1X or H3X temper tensile property limits.(E) Tests of F temper plate for tensile properties are not required.(F) The tension test specimen from plate over 12.50 mm in thickness is machined from the core and does not include the cladding alloy.(G) This material is subject to some recrystallization and an attendant loss of brightness.
Alloy
Temper
Specified Thickness,
mm
Axis of
Test Specimen
Tensile Strength,
MPa
Yield Strength
(0.2 % offset), MPa
Elongation,C
min, %
over
through
min
max
min
max
in 50 mm
in 5×
Diameter
2124
T851E
25.00
50.00
longitudinal
455
...
395
...
...
5
2124
T851E
long transverse
455
...
395
...
...
4
2124
T851E
short transverse
440J
...
380J
...
...
1
2124
T851E
50.00
80.00
longitudinal
450
...
395
...
...
5
2124
T851E
long transverse
450
...
395
...
...
3
2124
T851E
short transverse
435
...
380
...
...
1
2124
T851E
80.00
100.00
longitudinal
450
...
385
...
...
4
2124
T851E
long transverse
450
...
385
...
...
3
2124
T851E
short transverse
425
...
370
...
...
1
2124
T851E
100.00
130.00
longitudinal
440
...
380
...
...
4
2124
T851E
long transverse
440
...
380
...
...
3
2124
T851E
short transverse
420
...
365
...
...
1
2124
T851E
130.00
150.00
longitudinal
435
...
370
...
...
4
2124
T851E
long transverse
435
...
370
...
...
3
2124
T851E
short transverse
400
...
350
...
...
1
Alloy
Temper
Specified Thickness,
mm
Tensile Strength,
MPa
Yield Strength
(0.2 % offset), MPa
Elongation,C
min, %
over
through
min
max
min
max
in 50 mm
in 5×
Diameter
2219
O
0.50
12.50
...
220
...
110
12
...
2219
O
12.50
50.00
...
220
...
110
...
10
2219
T31K (flat sheet)
0.50
1.00
315
...
200
...
8
...
2219
T31K (flat sheet)
1.00
6.30
315
...
195
...
10
...
2219
T351E,H plate
(formerly T31 plate)
6.30
12.50
315
...
195
...
10
...
2219
T351E,H plate
(formerly T31 plate)
12.50
50.00
315
...
195
...
...
9
2219
T351E,H plate
(formerly T31 plate)
50.00
80.00
305
...
195
...
...
9
2219
T351E,H plate
(formerly T31 plate)
80.00
100.00
290
...
185
...
...
8
2219
T351E,H plate
(formerly T31 plate)
100.00
130.00
275
...
180
...
...
8
2219
T351E,H plate
(formerly T31 plate)
130.00
150.00
270
...
170
...
...
7
2219
T37K
0.50
1.00
340
...
260
...
6
...
2219
T37K
1.00
12.50
340
...
255
...
6
...
2219
T37K
12.50
60.00
340
...
255
...
...
5
2219
T37K
60.00
80.00
325
...
250
...
...
5
2219
T37K
80.00
100.00
310
...
240
...
...
4
2219
T37K
100.00
120.00
295
...
235
...
...
3
2219
T62F
0.50
1.00
370
...
250
...
6
...
2219
T62F
1.00
6.30
370
...
250
...
7
...
2219
T62F
6.30
12.50
370
...
250
...
8
...
2219
T62F
12.50
25.00
370
...
250
...
...
7
2219
T62F
25.00
50.00
370
...
250
...
...
6
2219
T81 sheet
0.50
1.00
425
...
315
...
6
...
2219
T81 sheet
1.00
6.30
425
...
315
...
7
...
2219
T851E
(formerly T81 plate)
6.30
12.50
425
...
315
...
8
...
2219
T851E
(formerly T81 plate)
12.50
25.00
425
...
315
...
...
7
2219
T851E
(formerly T81 plate)
25.00
50.00
425
...
315
...
...
6
2219
T851E
(formerly T81 plate)
50.00
80.00
425
...
310
...
...
5
2219
T851E
(formerly T81 plate)
80.00
100.00
415
...
305
...
...
4
2219
T851E
(formerly T81 plate)
100.00
130.00
405
...
295
...
...
4
2219
T851E
(formerly T81 plate)
130.00
150.00
395
...
290
...
...
3
2219
T87
0.50
1.00
440
...
360
...
5
...
2219
T87
1.00
6.30
440
...
360
...
6
...
2219
T87
6.30
12.50
440
...
350
...
7
...
2219
T87
12.50
25.00
440
...
350
...
...
6
2219
T87
25.00
80.00
440
...
350
...
...
5
2219
T87
80.00
100.00
425
...
345
...
...
3
2219
T87
100.00
120.00
420
...
340
...
...
2
2219
FG
6.30
50.00
...
...
...
...
...
...
Alclad 2219
O
0.50
1.00
...
220
...
110
12
...
Alclad 2219
O
1.00
2.50
...
220
...
110
12
...
Alclad 2219
O
2.50
12.50
...
220
...
110
12
...
Alclad 2219
O
12.50
50.00
...
220H
...
110H
...
10
Alclad 2219
T31K (flat sheet)
1.00
2.50
290
...
170
...
10
...
Alclad 2219
T31K (flat sheet)
2.50
6.30
305
...
180
...
10
...
Alclad 2219
T351E,K plate
(formerly T31 plate)
6.30
12.50
305
...
180
...
10
...
Alclad 2219
T37K
1.00
2.50
310
...
235
...
6
...
Alclad 2219
T37K
2.50
12.50
325
...
240
...
6
...
Alclad 2219
T62F
0.50
1.00
305
...
200
...
6
...
Alclad 2219
T62F
1.00
2.50
340
...
220
...
7
...
Alclad 2219
T62F
2.50
6.30
350
...
235
...
7
...
Alclad 2219
T62F
6.30
12.50
350
...
235
...
8
...
Alclad 2219
T62F
12.50
25.00
370H
...
250H
...
...
7
Alclad 2219
T62F
25.00
50.00
370H
...
250H
...
...
6
Alclad 2219
T81 (flat sheet)
0.50
1.00
340
...
255
...
6
...
Alclad 2219
T81 (flat sheet)
1.00
2.50
380
...
285
...
7
...
Alclad 2219
T81 (flat sheet)
2.50
6.30
400
...
295
...
7
...
Alclad 2219
T851E plate
(formerly T81 plate)
6.30
12.50
400
...
290
...
8
...
Alclad 2219
T87
1.00
2.50
395
...
315
...
6
...
Alclad 2219
T87
2.50
6.30
415
...
330
...
6
...
Alclad 2219
T87
6.30
12.50
415
...
330
...
7
...
Alclad 2219
FG
6.30
50.00
...
...
...
...
...
...
6013
T4
0.50
6.30
275
...
145
...
20
...
6013
T6
0.50
6.30
360
...
315
...
8
...
6013
T651E
6.30
40.00
365
...
305
...
...
4
6013
T651E
40.00
80.00
370
...
325
...
...
4
6013
T651E
80.00
160.00
380
...
325
...
...
3
6061
O
0.15
0.20
...
150
...
85
10
...
6061
O
0.20
0.25
...
150
...
85
12
...
6061
O
0.25
0.50
...
150
...
85
14
...
6061
O
0.50
3.20
...
150
...
85
16
...
6061
O
3.20
12.50
...
150
...
85
18
...
6061
O
12.50
25.00
...
150
...
...
...
16
6061
O
25.00
80.00
...
150
...
...
...
14
6061
T4
0.15
0.20
205
...
110
...
10
...
6061
T4
0.20
0.25
205
...
110
...
12
...
6061
T4
0.25
0.50
205
...
110
...
14
...
6061
T4
0.50
6.30
205
...
110
...
16
...
6061
T451E
6.30
12.50
205
...
110
...
18
...
6061
T451E
12.50
25.00
205
...
110
...
...
16
6061
T451E
25.00
80.00
205
...
110
...
...
14
6061
T42F
0.15
0.20
205
...
95
...
10
...
6061
T42F
0.20
0.25
205
...
95
...
12
...
6061
T42F
0.25
0.50
205
...
95
...
14
...
6061
T42F
0.50
6.30
205
...
95
...
16
...
6061
T42F
6.30
12.50
205
...
95
...
18
...
6061
T42F
12.50
25.00
205
...
95
...
...
16
6061
T42F
25.00
80.00
205
...
95
...
...
14
6061
T6, T62F
0.15
0.20
290
...
240
...
4
...
6061
T6, T62F
0.20
0.25
290
...
240
...
6
...
6061
T6, T62F
0.25
0.50
290
...
240
...
8
...
6061
T6, T62F
0.50
6.30
290
...
240
...
10
...
6061
T62F, T651E
6.30
12.50
290
...
240
...
10
...
6061
T62F, T651E
12.50
25.00
290
...
240
...
...
8
6061
T62F, T651E
25.00
50.00
290
...
240
...
...
7
6061
T62F, T651E
50.00
100.00
290
...
240
...
...
5
6061
T62F, T651E
100.00
150.00L
275
...
240
...
...
5
6061
FG
6.30
80.00
...
...
...
...
...
...
Alclad 6061
O
0.24
0.50
...
140
...
85
14
...
Alclad 6061
O
0.50
3.20
...
140
...
85
16
...
Alclad 6061
O
3.20
12.50
...
140
...
85
18
...
Alclad 6061
O
12.50
25.00
...
150H
...
...
...
16
Alclad 6061
O
25.00
80.00
...
150H
...
...
...
14
Alclad 6061
T4
0.24
0.50
185
...
95
...
14
...
Alclad 6061
T4
0.50
6.30
185
...
95
...
16
...
Alclad 6061
T451E
6.30
12.50
185
...
95
...
18
...
Alclad 6061
T451E
12.50
25.00
205H
...
110H
...
...
16
Alclad 6061
T451E
25.00
80.00
205H
...
110H
...
...
14
Alclad 6061
T42F
0.24
0.50
185
...
85
...
14
...
Alclad 6061
T42F
0.50
6.30
185
...
85
...
16
...
Alclad 6061
T42F
6.30
12.50
185
...
85
...
18
...
Alclad 6061
T42F
12.50
25.00
205H
...
95H
...
...
16
Alclad 6061
T42F
25.00
80.00
205H
...
95H
...
...
14
Alclad 6061
T6, T62F
0.24
0.50
260
...
220
...
8
...
Alclad 6061
T6, T62F
0.50
6.30
260
...
220
...
10
...
Alclad 6061
T62F, T651E
6.30
12.50
260
...
220
...
10
...
Alclad 6061
T62F, T651E
12.50
25.00
290H
...
240H
...
...
8
Alclad 6061
T62F, T651E
25.00
50.00
290H
...
240H
...
...
7
Alclad 6061
T62F, T651E
50.00
100.00
290H
...
240H
...
...
5
Alclad 6061
T62F, T651E
100.00
120.00L
275H
...
240H
...
...
5
Alclad 6061
FG
6.30
80.00
...
...
...
...
...
...
7075
O
0.39
12.50
...
275
...
145
10
...
7075
O
12.50
50.00
...
275
...
...
...
9
7075
T6, T62F
0.19
0.32
510
...
435
...
5
...
7075
T6, T62F
0.32
1.00
525
...
460
...
8
...
7075
T6, T62F
1.00
3.20
540
...
470
...
9
...
7075
T6, T62F
3.20
4.70
545
...
475
...
9
...
7075
T6, T62F
4.70
6.30
550
...
475
...
9
...
7075
T62F, T651E
6.30
12.50
540
...
460
...
9
...
7075
T62F, T651E
12.50
25.00
540
...
470
...
...
6
7075
T62F, T651E
25.00
50.00
530
...
460
...
...
5
7075
T62F, T651E
50.00
60.00
525
...
440
...
...
4
7075
T62F, T651E
60.00
80.00
495
...
420
...
...
4
7075
T62F, T651E
80.00
90.00
490
...
400
...
...
4
7075
T62F, T651E
90.00
100.00
460
...
370
...
...
2
7075
T73 sheet
1.00
6.30
460
...
385
...
8
...
7075
T7351E plate
6.30
12.50
475
...
390
...
7
...
7075
T7351E plate
12.50
25.00
475
...
390
...
...
6
7075
T7351E plate
25.00
50.00
475
...
390
...
...
5
7075
T7351E plate
50.00
60.00
455
...
360
...
...
5
7075
T7351E plate
60.00
80.00
440
...
340
...
...
5
7075
T7351E plate
80.00
90.00
435
...
340
...
...
5
7075
T7351E plate
90.00
100.00
420
...
330
...
...
5
7075
T76 sheet
1.60
6.30
505
...
425
...
8
...
7075
T7651E plate
6.30
12.50
495
...
420
...
8
...
7075
T7651E plate
12.50
25.00
490
...
415
...
...
5
7075
FG
6.30
100.00
...
...
...
...
...
...
Alclad 7075
O
0.19
0.40
...
250
...
140
9
...
Alclad 7075
O
0.40
1.60
...
250
...
140
10
...
Alclad 7075
O
1.60
4.00
...
260
...
140
10
...
Alclad 7075
O
4.00
12.50
...
270
...
145
10
...
Alclad 7075
O
12.50
25.00
...
275H
...
...
...
9
Alclad 7075
T6, T62F
0.19
0.32
470
...
400
...
5
...
Alclad 7075
T6, T62F
0.32
1.00
490
...
420
...
8
...
Alclad 7075
T6, T62F
1.00
1.60
495
...
425
...
9
...
Alclad 7075
T6, T62F
1.60
3.20
510
...
440
...
9
...
Alclad 7075
T6, T62F
3.20
4.70
510
...
440
...
9
...
Alclad 7075
T6, T62F
4.70
6.30
525
...
450
...
9
...
Alclad 7075
T62F, T651E
6.30
12.50
515
...
445H
...
9
...
Alclad 7075
T62F, T651E
12.50
25.00
540H
...
470H
...
...
6
Alclad 7075
T62F, T651E
25.00
50.00
530H
...
460H
...
...
5
Alclad 7075
T62F, T651E
50.00
60.00
525H
...
440H
...
...
4
Alclad 7075
T62F, T651E
60.00
80.00
495H
...
420H
...
...
4
Alclad 7075
T62F, T651E
80.00
90.00
490H
...
400H
...
...
4
Alclad 7075
T62F, T651E
90.00
100.00
460H
...
370H
...
...
2
Alclad 7075
T76 sheet
1.00
1.60
460
...
385
...
8
...
Alclad 7075
T76 sheet
1.60
4.70
470
...
395
...
8
...
Alclad 7075
T76 sheet
4.70
6.30
485
...
405
...
8
...
Alclad 7075
T7651E plate
6.30
12.50
475
...
400
...
8
...
Alclad 7075
T7651E plate
12.50
25.00
490H
...
415H
...
...
5
Alclad 7075
FG
6.30
100.00
...
...
...
...
...
...
Alclad 1-Side 7075
O
0.39
1.60
...
260
...
145
10
...
Alclad 1-Side 7075
O
1.60
4.00
...
270
...
145
10
...
Alclad 1-Side 7075
O
4.00
12.50
...
270
...
145
10
...
Alclad 1-Side 7075
O
12.50
25.00
...
275H
...
...
...
9
Alclad 1-Side 7075
T6, T62F
0.19
0.32
490
...
415
...
5
...
Alclad 1-Side 7075
T6, T62F
0.32
1.00
510
...
440
...
8
...
Alclad 1-Side 7075
T6, T62F
1.00
1.60
515
...
450
...
9
...
Alclad 1-Side 7075
T6, T62F
1.60
3.20
525
...
455
...
9
...
Alclad 1-Side 7075
T6, T62F
3.20
4.70
530
...
460
...
9
...
Alclad 1-Side 7075
T6, T62F
4.70
6.30
540
...
460
...
9
...
Alclad 1-Side 7075
T62F, T651E
6.30
12.50
525
....
455
...
9
...
Alclad 1-Side 7075
T62F, T651E
12.50
25.00
540H
...
470H
...
...
6
Alclad 1-Side 7075
T62F, T651E
25.00
50.00
530H
...
460H
...
...
5
Alclad 1-Side 7075
FG
6.30
50.00
...
...
...
...
...
...
(A) To determine conformance to this specification, each value for tensile strength shall be rounded to the nearest 1 MPa and each value for elongation to the nearest 0.5 %, both in accordance with the Rounding Method of Practice E29.(B) The basis for establishment of mechanical property limits is shown in Annex AI.(C) Elongations in 50 mm apply for thicknesses up through 12.50 mm and in 5× diameter for thicknesses over 12.50 mm.(D) Coiled sheet.(E) For stress-relieved tempers (T351, T451, T651, T7351, T7651, and T851), characteristics and properties other than those specified may differ somewhat from the corresponding characteristics and properties of material in the basic temper.(F) Material in the T42, T62, and T72 tempers is not available from the material producer.(G) Test for tensile properties in the F temper are not required.(H) The tension test specimen from plate over 12.50 mm in thickness is machined from the core and does not include the cladding.(I) The T72 temper is applicable only to Alloys 2024 and Alclad 2024 sheet solution heat treated and artificially overaged by the user to develop increased resistance to stress-corrosion cracking.(J) Short transverse tensile properties are not applicable to material less than 40 mm in thickness.(K) Use of Alloys 2219 and Alclad 2219 in the T31, T351, and T37 tempers for finished products is not recommended.(L) The properties for this thickness apply only to the T651 temper.1.1.1 Plate in all alloys and sheet in heat-treatable alloys: mill finish.
1.1.2 Sheet in nonheat-treatable alloys: mill finish, one-side bright mill finish, standard one-side bright finish, and standard two-sides bright finish.
1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1(M). The equivalent Unified Numbering System (UNS) alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527.
Note 1: Throughout this specification, use of the term alloy in the general sense includes aluminum as well as aluminum alloy.
Note 2: See Specification B632/B632M for Tread Plate.
Note 3: See Specification B928/B928M for 5xxx-H116 and 5xxx-H321 aluminum alloys containing 3 % or more nominal magnesium and intended for marine service and similar environments. Other alloy-temper products listed in Specification B209, which do not require the additional corrosion testing/capability called out in Specification B928/B928M, may be suitable for marine and similar environment applications.
1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.
1.4 This specification is the SI companion to Specification B209.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.