Каталог стандартов

+7 (495) 223-46-76 +7 (812) 309-78-59
inform@normdocs.ru

ASTM B581-02(2013)e1

Заменен
Standard Specification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Rod — 4 стр.
Реферат

This specification covers nickel-chromium-iron-molybdenum-copper alloy rods (UNS N06007, N06975, N06985, N06030, and N08031), hot- or cold-finished, solution annealed, ground, or turned, for use in general corrosive service. Heat and product (check) analysis of the alloy shall conform to the chemical composition requirements prescribed for nickel, chromium, iron, molybdenum, copper, manganese, cobalt, carbon, tungsten, silicon, phosphorus, sulfur, columbium and tantalum, titanium, and nitrogen. The material shall conform to the specified straightness criteria and to the mechanical property requirements including tensile strength, yield strength, and elongation, as determined by tension test.

Область применения

1.1 This specification2 covers rod of Ni-Cr-Fe-Mo-Cu alloys (UNS N06007, N06975, N06985, N06030, and N08031)* as shown in Tables 1-3, for use in general corrosive service.

TABLE 1 Chemical Requirements

Element

Composition Limits, %

 

Alloy N06007

Alloy N06975

Alloy N06985

Alloy N06030

Alloy N08031

Nickel

remainderA

47.0–52.0

remainderA

remainderA

30.0-32.0

Chromium

21.0–23.5

23.0–26.0

21.0–23.5

28.0–31.5

26.0-28.0

Iron

18.0–21.0

remainderA

18.0–21.0

13.0–17.0

remainderA

Molybdenum

5.5–7.5

5.0–7.0

6.0–8.0

4.0–6.0

6.0-7.0†

Copper

1.5–2.5

0.70–1.20

1.5–2.5

1.0–2.4

1.0-1.4

Manganese

1.0–2.0

1.0 max

1.0 max

1.5 max

2.0 max

Cobalt, max

2.5

...

5.0 max

5.0 max

...

Carbon, max

0.05

0.03

0.015 max

0.03 max

0.015

Tungsten

1.0 max

...

1.5 max

1.5–4.0

...

Silicon, max

1.0

1.0

1.0 max

0.8 max

0.3

Phosphorus, max

0.04

0.03

0.04 max

0.04 max

0.020

Sulfur, max

0.03

0.03

0.03 max

0.02 max

0.010

Columbium + tantalum

1.75–2.50

...

0.50 max

0.30–1.50

...

Titanium

...

0.7–1.5

...

...

...

Nitrogen

0.15-0.25

...

...

...

...

A See 13.1.1.

†Editorially corrected.

TABLE 2 Mechanical Property Requirements

Alloy

Specified Diameter, in. (mm)

Tensile Strength min, psi (MPa)

Yield Strength (0.2 % Offset), min, psi (MPa)

Elongation in 2 in. or 50.8 mm or 4D A min

N06007

5/16 to 3/4 (7.94 to 19.05), incl

90 000 (621)

35 000 (241)

35

 

Over 3/4 to 31/2 (19.05 to 88.9), incl

85 000 (586)

30 000 (207)

30

N06975

5/16 to 31/2 (7.94 to 88.9), incl

85 000 (586)

32 000 (221)

40

N06985

5/16 to 3/4 (7.9 to 19.05), incl

90 000 (621)

35 000 (241)

45

 

Over 3/4 to 31/2 (19.05 to 88.9), incl

85 000 (586)

30 000 (207)

35

N06030

...

85 000 (586)

35 000 (241)

30

N08031

All sizes

94 000 (648)

40 000 (276)

40

AD refers to the diameter of the tension specimen.TABLE 3 Permissible Variations in Diameter and Out-of-Roundness of Rods

Specified Diameter, in. (mm)

Permissible Variations, in. (mm)

Diameter

Out-of-Roundness, max

 + 

Hot-Finished, Annealed, and Descaled Rods

5/16 to 7/16 (7.94 to 11.11), incl

0.012 (0.305)

0.012 (0.305)

0.018 (0.457)

Over 7/16 to 5/8 (11.11 to 15.87), incl

0.014 (0.355)

0.014 (0.355)

0.020 (0.508)

Over 5/8 to 3/4 (15.87 to 19.05), excl

0.016 (0.406)

0.016 (0.406)

0.024 (0.610)

Hot-Finished, Annealed, and Ground or Turned Rods

3/4 to 31/2 (19.05 to 88.9), incl

0.010 (0.254)

0

0.008 (0.203)


1.2 The following products are covered under this specification:

1.2.1 Rods 5/16 to 3/4 in. (7.94 to 19.05 mm) excl in diameter, hot- or cold-finished, solution annealed and pickled or mechanically descaled.

1.2.2 Rods 3/4 to 31/2 in. (19.05 to 88.9 mm) incl in diameter, hot- or cold-finished, solution annealed, ground or turned.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

ICS
77.150.40 Nickel and chromium products / Продукция из никеля и хрома
Сборник ASTM
02.04 Nonferrous Metals – Nickel, Titanium, Lead, Tin, Zinc, Zirconium, Precious, Reactive, Refractory Metals and Alloys: Materials for Thermostats, Electrical Heating and Resistance Contact, and Connectors / Цветные металлы - Никель, Кобальт, Свинец, Олово, Цинк, Кадмий, Драгоценные металлы, химически активные металлы, Тугоплавкие металлы и сплавы, Материалы для Термостатов, Электронагревательных приборов, Контактов, Соединительные устройств
Тематика
Other Nonferrous Metals