Каталог стандартов

+7 (495) 223-46-76 +7 (812) 309-78-59
inform@normdocs.ru

ASTM B582-07(2013)

Заменен
Standard Specification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Plate, Sheet, and Strip — 3 стр.
Реферат

This specification deals with the standard requirements for nickel-chromium-iron-molybdenum-copper alloys (UNS N06007, N06975, N06985, and N06030) in the form of plate, sheet, and strip for use in general corrosive services. These materials shall undergo hot or cold rolling, solution annealing, and descaling. The plates shall have sheared or cut machined, abrasive cut, powder cut, or inert arc cut edges while the sheet and strip shall have sheared or slit edges. Heat and product analysis shall be performed to determine the chemical composition of the specimens which shall conform to the specified nickel, chromium, iron, molybdenum, copper, manganese, cobalt, carbon, tungsten, silicon, phosphorus, sulfur, columbium, tantalum, and titanium limits. The materials shall also conform to the mechanical property requirements for tensile strength, yield strength, elongation, and Rockwell hardness.

Область применения

1.1 The specification2 covers plate, sheet, and strip of nickel-chromium-iron-molybdenum-copper alloys (UNS N06007, N06975, N06985, and N06030)* as shown in Table 1, for use in general corrosive service.

TABLE 1 Chemical Requirements

Element

Composition Limits, %

 

Alloy N06007

Alloy N06975

Alloy N06985

Alloy N06030

Nickel

 

remainderA

47.0 to 52.0

remainderA

remainderA

Chromium

 

21.0 to 23.5

23.0 to 26.0

21.0 to 23.5

28.0 to 31.5

Iron

 

18.0 to 21.0

remainderA

18.0 to 21.0

13.0 to 17.0

Molybdenum

 

5.5 to 7.5

5.0 to 7.0

6.0 to 8.0

4.0 to 6.0

Copper

 

1.5 to 2.5

0.70 to 1.20

1.5 to 2.5

1.0 to 2.4

Manganese

 

1.0 to 2.0

1.0 max

1.0 max

1.5 max

Cobalt, max

 

2.5

...

5.0

5.0

Carbon, max

 

0.05

0.03

0.015

0.03

Tungsten

 

1.0 max

...

1.5 max

1.5 to 4.0

Silicon, max

 

1.0

1.0

1.0

0.8

Phosphorus, max

 

0.04

0.03

0.04

0.04

Sulfur, max

 

0.03

0.03

0.03

0.02

Columbium + tantalum

 

1.75 to 2.50

...

0.50 max

0.30 to 1.50

Titanium

 

...

0.70–1.50

...

...

A The composition of the remainder element shall be determined arithmetically by difference.

1.2 The following products are covered under this specification:

1.2.1 Sheet and Strip—Hot or cold rolled, solution annealed, and descaled unless solution anneal is performed in an atmosphere yielding a bright finish.

1.2.2 Plate—Hot or cold rolled, solution annealed, and descaled.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

ICS
77.150.40 Nickel and chromium products / Продукция из никеля и хрома
Сборник ASTM
02.04 Nonferrous Metals – Nickel, Titanium, Lead, Tin, Zinc, Zirconium, Precious, Reactive, Refractory Metals and Alloys: Materials for Thermostats, Electrical Heating and Resistance Contact, and Connectors / Цветные металлы - Никель, Кобальт, Свинец, Олово, Цинк, Кадмий, Драгоценные металлы, химически активные металлы, Тугоплавкие металлы и сплавы, Материалы для Термостатов, Электронагревательных приборов, Контактов, Соединительные устройств
Тематика
Other Nonferrous Metals