This specification covers seamless pipe and tube of nickel and nickel-cobalt alloys. These alloys are classified into different grades according to chemical composition. Mechanical properties of the material like tensile strength, yield strength, and elongation shall be measured. Tension, hydrostatic, and nondestructive electric tests shall be done on each pipe or tube. The mass or weight of each pipe shall be calculated and the chemical composition of each pipe shall be determined.
Область применения1.1 This specification2 covers seamless pipe and tube of nickel and nickel-cobalt alloys (UNS N10001, UNS N10242, UNS N10665, UNS N12160, UNS N10675, UNS N10276, UNS N06455, UNS N06007, UNS N08320, UNS N06975, UNS N06002, UNS N06985, UNS N06022, UNS N06035, UNS N06044, UNS N08135, UNS N06255, UNS N06058, UNS N06059, UNS N06200, UNS N10362, UNS N06030, UNS N08031, UNS R30556, UNS N08535, UNS N06250, UNS N06060, UNS N06230, UNS N06686, UNS N10629, UNS N06210, UNS N10624, and UNS R20033)3 as shown in Table 1.
TABLE 1 Chemical Requirements
Composition Limits, %
Ni
Cr
Mo
Fe
W
C
Si
max
Co
Mn
V
P
max
S
max
Ti
Cu
Cb
(Nb)
+Ta
Al
Zr
La
N
B
Cb
(Nb)
Ta
Ni+
Mo
Mg
Ni-Mo Alloys
N10001
remainder
A
1.0 max
26.0- 30.0
4.0-6.0
...
0.05 max
1.0
2.5 max
1.0 max
0.2- 0.4
0.04
0.03
...
...
...
N10665
remainder
A
1.0 max
26.0- 30.0
2.0 max
...
0.02 max
0.10
1.0 max
1.0 max
...
0.04
0.03
...
...
...
N10675
65.0 min
1.0- 3.0
27.0- 32.0
1.0-3.0
3.0 max
0.01 max
0.10
3.0 max
3.0 max
0.20 max
0.030
0.010
0.20 max
0.20 max
...
0.50 max
0.10 max
...
...
...
0.20 max
0.20 max
94.0- 98.0
N10629
remainder
A
0.5- 1.5
26.0- 30.0
1.0-6.0
...
0.01 max
0.05
2.5 max
1.5 max
...
0.04
0.01
...
0.5 max
...
0.1- 0.5
...
...
...
...
...
...
...
N10624
remainder
A
6.0- 10.0
21.0- 25.0
5.0-8.0
...
0.01 max
0.10
1.0 max
1.0 max
...
0.025
0.01
...
0.5 max
...
...
...
...
...
...
...
...
...
Ni-Mo-Cr-Fe Alloy
N10242
remainder
A
7.0- 9.0
24.0- 26.0
2.0 max
0.03 max
0.80
1.00 max
0.80 max
0.030
0.015
0.50 max
0.50 max
0.006 max
Low C Ni-Cr-Mo Alloys
N10276
remainder
A
14.5- 16.5
15.0- 17.0
4.0-7.0
3.0- 4.5
0.010 max
0.08
2.5 max
1.0 max
0.35 max
0.04
0.03
...
...
...
N06022
remainder
A
20.0- 22.5
12.5- 14.5
2.0-6.0
2.5- 3.5
0.015 max
0.08
2.5 max
0.50 max
0.35 max
0.02
0.02
...
...
...
N06035
remainder
A
32.25-
34.25
7.60-
9.00
2.00 max
0.60 max
0.050 max
0.60
1.00 max
0.50 max
0.20 max
0.030
0.015
...
0.30 max
...
0.40 max
...
...
...
...
...
...
...
...
N06044
balance
43.5-
45.3
0.80-
1.20
0.3 max
...
0.02 max
0.20
...
0.07-
0.30
...
0.020
0.020
0.10-
0.30
...
...
0.30 max
...
...
...
...
...
...
...
...
N06058
balance
20.0- 23.0
18.5- 21.0
1.5 max
0.3 max
0.010 max
0.10 max
0.3 max
0.50 max
0.015
0.010
...
0.50 max
...
0.40 max
0.02- 0.15
N06059
balance
22.0- 24.0
15.0- 16.5
1.5 max
...
0.010 max
0.10
0.3 max
0.5 max
...
0.015
0.010
...
0.50 max
...
0.1- 0.4
...
...
...
...
...
...
...
N06455
remainder
A
14.0- 18.0
14.0- 17.0
3.0 max
...
0.015 max
0.08
2.0 max
1.0 max
...
0.04
0.03
0.70 max
...
...
Ni-Cr-Fe-Mo-Cu Alloys
N06007
remainder
A
21.0- 23.5
5.5- 7.5
18.0-21.0
1.0 max
0.05 max
1.0
2.5 max
1.0- 2.0
...
0.04
0.03
...
1.5- 2.5
1.75- 2.5
N06975
47.0-52.0
23.0- 26.0
5.0- 7.0
remainder
A
...
0.03 max
1.0
...
1.0 max
...
0.03
0.03
0.70- 1.50
0.70- 1.20
...
N06985
remainder
A
21.0- 23.5
6.0- 8.0
18.0-21.0
1.5 max
0.015 max
1.0
5.0 max
1.0 max
...
0.04
0.03
...
1.5- 2.5
0.50 max
N06030
remainder
A
28.0- 31.5
4.0-6.0
13.0-17.0
1.5- 4.0
0.03 max
0.8
5.0 max
1.5 max
...
0.04
0.02
...
1.0- 2.4
0.30- 1.50
N06255
47.0-52.0
23.0- 26.0
6.0-9.0
remainder
A
3.0 max
0.03 max
1.0
...
1.0 max
...
0.03
0.03
0.69 max
1.2 max
...
N06250
50.0-54.0
20.0- 23.0
10.1-12.0
remainder
A
0.25- 1.25
0.020 max
0.09
...
1.00 max
...
0.030
0.005
...
0.25- 1.25
...
Ni-Fe-Cr-Mo Alloys
N08320
25.0-27.0
21.0- 23.0
4.0- 6.0
remainder
A
...
0.05 max
1.0
...
2.5 max
...
0.04
0.03
4xC min
...
...
N08135
33.0-38.0
20.5- 23.5
4.0- 5.0
remainder
A
0.20- 0.80
0.030 max
0.75
...
1.00 max
...
0.03
0.03
...
N06002
remainder
A
20.5- 23.0
8.0- 10.0
17.0-20.0
0.20- 1.0
0.05- 0.15
1.0
0.5-2.5
1.0 max
...
0.04
0.03
...
...
...
N06060
54.0–60.0
19.0- 22.0
12.0- 14.0
remainder
A
0.25- 1.25
0.03 max
0.50
...
1.50 max
...
0.030 max
0.005 max
...
0.25- 1.25
0.50- 1.25
Ni-Fe-Cr-Co Alloy
R30556
19.0-22.5
21.0- 23.0
2.5- 4.0
remainder
A
2.0- 3.5
0.05- 0.15
0.20- 0.80
16.0- 21.0
0.50- 2.00
...
0.04
0.015
...
...
...
0.10- 0.50
0.001- 0.10
0.005- 0.10
0.10- 0.30
0.02 max
0.30 max
0.3- 1.25
Ni-Cr-W-Mo Alloys
N06230
remainder
A
20.0- 24.0
1.0- 3.0
3.0 max
13.0- 15.0
0.05- 0.15
0.25- 0.75
5.0 max
0.30- 1.00
...
0.03
0.015
...
...
...
0.50 max
...
0.005- 0.050
...
0.015 max
...
...
Low C-Ni-Cr-Mo-Cu Alloy
N06200
remainder
A
22.0- 24.0
15.0- 17.0
3.0 max
...
0.010 max
0.08
2.0 max
0.50 max
...
0.025
0.010
...
1.3- 1.9
...
0.50 max
Low C-Ni-Mo-Cr Alloy
N10362
remainder
A
13.8-
15.6
21.5-23.0
1.25 max
...
0.010 max
0.08
...
0.60 max
...
0.025
0.010
...
...
...
0.50 max
...
...
...
...
...
...
...
...
Low C-Ni-Fe-Cr-Mo-Cu Alloys
N08031
30.0-32.0
26.0- 28.0
6.0- 7.0
balance
...
0.015 max
0.3
...
2.0 max
...
0.020
0.010
...
1.0- 1.4
...
...
...
...
0.15- 0.25
...
...
...
N08535
29.0-36.5
24.0- 27.0
2.5- 4.0
remainder
A
...
0.03 max
0.50
...
1.0 max
...
0.03
0.03
...
1.50 max
Low C-Ni-Cr-Mo-W Alloy
N06686
remainder
A
19.0- 23.0
15.0- 17.0
5.0 max
3.0- 4.4
0.010 max
0.08
...
0.75 max
...
0.04
0.02
0.02- 0.25
...
...
...
...
...
...
...
...
...
Ni-Co-Cr-Si Alloy
N12160
remainder
A
26.0- 30.0
1.0 max
3.5 max
1.0 max
0.15 max
2.4- 3.0
27.0- 33.0
1.5 max
...
0.030
0.015
0.20- 0.80
...
...
...
...
...
...
...
1.0 max
...
...
...
Cr-Ni-Fe-N Alloy
R20033
30.0-33.0
31.0- 35.0
0.50- 2.0
balance
...
0.015 max
0.50
...
2.0 max
...
0.02
0.01
...
0.3- 1.20
...
...
...
...
0.35- 0.60
...
...
...
...
...
Low C-Ni-Mo-Cr-Ta Alloy
N06210
remainder
A
18.0- 20.0
18.0- 20.0
1.0 max
...
0.015 max
0.08
1.0 max
0.5 max†
0.35 max
0.02
0.02
...
...
...
...
...
...
...
1.5-2.2
(A) See 12.1.
†Editorially corrected.
1.2 Pipe and tube shall be supplied in the solution annealed and descaled condition. When atmosphere control is used, descaling is not necessary.
1.3 This specification is limited to tubes up to and including 3.5 in. (88.9 mm) outside diameter.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.