4.1 The purpose of these color codes is to allow for quick identification of ingot bundles or jumbo ingots of alloys used for hot-dip galvanizing. Other than jumbo ingots, this standard is not intended to imply that each ingot will be color-coded but only that each ingot bundle be color coded.
4.2 Each ingot bundle or jumbo ingot shall be identified with the appropriate color code listed in Table 1.
TABLE 1 Color Codes for Zinc and Zinc Alloys Used for Hot Dip GalvanizingAlloy
UNSA
ASTM
Standard
Nominal Composition
Color Code
Al
Other
North AmericaB
International
Primary Zinc GradesC
SHG
(Z13001)
Yellow
Yellow
HG
(Z14003)
Green
Green
PW
(Z18005)
Pb–1.0 %
Black
Black
CGG Alloys
(Z80310)
0.25
Brown/Brown
Yellow/Brown
(Z80411)
0.35
Blue/Blue
Yellow/Blue
(Z80511)
0.45
Purple/Purple
Yellow/Purple
(Z80531)
0.45
Pb–0.02 %
Red/Red
Yellow/Red
(Z80610)
0.55
Pink/Pink
Yellow/Pink
(Z80710)
0.65
Green/Green
Yellow/Green
(Z80810)
0.75
Black/Black
Yellow/Black
(Z80910)
1.00
Orange/Orange
Yellow/Orange
Master Alloys
Type A-1
(Z30750)
10.0
High Purity
Red/Green
Yellow/Red/Green
Type A-2
(Z31710)
10.0
Low Purity
Red/Black
Yellow/Red/Black
Type A-3
(Z30503)
5.0
High Purity
Red/Blue
Yellow/Red/Blue
Type A-4
(Z31510)
5.0
Low Purity
Red/Yellow
Yellow/Red/Yellow
Type A-5
(Z31520)
4.0
High Purity
Red/Brown
Yellow/Red/Brown
Type A-6
(Z30504)
4.0
Low Purity
Red/Purple
Yellow/Red/Purple
Type S-1
(Z55710)
Sb–10.0 %
Black/Green
Yellow/Black/Green
Specialty Alloys
GALFAND
(Z38510)
5.0
Mischmetal
Purple/Blue
Yellow/Purple/Blue
GALVALUMEE
55.0
Si–1.5 %
Orange/Green
Yellow/Orange/Green
A UNS assignations were established in accordance with Practice E527. The last digit of a UNS number differentiates between alloys of similar composition.B The North American system is designed to be a simplified version of the International system by eliminating the leading yellow stripe.C Color codes taken from European Standard EN 1179.D GALFAN is a registered trademark of the GALFAN Information Center, Inc.E GALVALUME is a registered trademark of BIEC International Inc., USA.4.3 The color will be applied as a stripe, or stripes, on two adjacent sides of the ingot bundle or jumbo ingot. The color stripes will be applied to include the ingot bundle foot.
4.4 When using multiple stripes, the colored stripes will be applied from left to right as indicated in Table 1.
4.5 In the absence of a written agreement to the contrary between the supplier and end user, the North American color code will be the standard for all North American transactions; for all other transactions the International Color Code will be used.
Область применения1.1 This standard is published with the following objectives:
1.1.1 To establish standard color codes for zinc, zinc alloy and zinc master alloy ingot used by the Hot-Dip Galvanizing industry, and
1.1.2 To standardize the use and application of these color codes.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.