Значение и использование

This test method is intended for use as a guide in cases where experimental determination of heat of combustion is not available and cannot be made conveniently and where an estimate is considered satisfactory. It is not intended as a substitute for experimental measurements of heat of combustion. Table 1 shows a summary for the range of each variable used in developing the correlation. The mean value and an estimate of its distribution about the mean, namely the standard deviation, is shown. This indicates, for example, that the mean density for all fuels used in developing the correlation was 779.3 kg/m³ and that two thirds of the samples had a density between 721.4 and 837.1 kg/m³, that is, plus or minus one standard deviation. The correlation is most accurate when the values of the variables used are within one standard deviation of the mean, but is useful up to two standard deviations of the mean. The use of this correlation may be applicable to other hydrocarbon distillates and pure hydrocarbons; however, only limited data on non-aviation fuels over the entire range of the variables were included in the correlation.

Note 3—The procedures for the experimental determination of the gross and net heats of combustion are described in Test Methods D 240 and D 4809.

The calorimetric methods cited in Note 3 measure gross heat of combustion. However, net heat is used in aircraft calculations because all combustion products are in the gaseous state. This calculation method is based on net heat, but a correction is required for condensed sulfur compounds.

TABLE 1 Mean and Standard Deviation of the Variables

VariableMeanStandard
Deviation Aromatics, volume %13.523.9 Density, kg/m³ (°API)779.3 (50.0)58.0 (13.5) Volatility, °C (°F)171.11 (340)57.2 (103) Heat of combustion, MJ/kg (Btu/lb)43.421 (18 668)0.862 (371) Область применения

1.1 This test method covers the estimation of the net heat of combustion (megajoules per kilogram or Btu per pound) of aviation gasolines and aircraft turbine and jet engine fuels.

1.2 This test method is purely empirical and is applicable to liquid hydrocarbon fuels that conform to the specifications for aviation gasolines or aircraft turbine and jet engine fuels of grades Jet A, Jet A-1, Jet B, JP-4, JP-5, JP-7, and JP-8.

Note 1—The experimental data on heat of combustion from which the Test Method D 3338 correlation was devised was obtained by a precision method similar to Test Method D 4809.

Note 2—The estimation of the net heat of combustion of a hydrocarbon fuel is justifiable only when the fuel belongs to a well-defined class for which a relation between heat of combustion and aromatic and sulfur contents, density, and distillation range of the fuel has been derived from accurate experimental measurements on representative samples of that class. Even in this case, the possibility that the estimates may be in error by large amounts for individual fuels should be recognized. The fuels used to establish the correlation presented in this method are defined as follows:

Fuels: Aviation gasoline—Grades 100/130 and 115/145 (1, 2) Kerosines, alkylates, and special WADC fuels (3) Pure hydrocarbons—paraffins, naphthenes, and aromatics (4) Fuels for which data were reported by the Coordinating Research Council (5).

1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3.1 Although the test method permits the calculation of net heat of combustion in either SI or inch-pound units, SI units are the preferred units.

1.3.2 The net heat of combustion can also be estimated in inch-pound units by Test Method D 1405 or in SI units by Test Method D 4529. Test Method D 1405 requires calculation of one of four equations dependent on the fuel type with a precision equivalent to that of this test method. Test Method D 4529 requires calculation of a single equation for all aviation fuels with a precision equivalent to that of this test method. Unlike Test Method D 1405 and D 4529, Test Method D 3338 does not require the use of aniline point.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.