Каталог стандартов

+7 (495) 223-46-76 +7 (812) 309-78-59
inform@normdocs.ru

ASTM D3343-05(2015)

Заменен
Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels — 5 стр.
Значение и использование

4.1 This test method is intended for use as a guide in cases in which an experimental determination of hydrogen content is not available. Table 1 shows a summary for the range of each variable used in developing the correlation. The mean value and its distribution about the mean, namely the standard deviation, is shown. This indicates, for example, that the mean density for all fuels used in developing the correlation was 783.5 kg/m3 and that two thirds of the samples had a density between 733.2 kg/m3 and 841.3 kg/m3, that is, plus and minus one standard deviation. The correlation is most accurate when the values of the variables to be used in the equation are within one standard deviation of the mean, but is useful up to two standard deviations of the mean. The use of this correlation may be applicable to other hydrocarbon distillates similar to aviation fuels, but only limited data on nonaviation fuels were included in the correlation.

4.2 Hydrogen content is required to correct gross heat of combustion to net heat of combustion. Net heat is used in aircraft calculation because all combustion products are in the gaseous state, but experimental methods measure gross heat.

Область применения

1.1 This test method covers the estimation of the hydrogen content (mass percent) of aviation gasolines and aircraft turbine and jet engine fuels.

1.2 This test method is empirical and is applicable to liquid hydrocarbon fuels that conform to the requirements of specifications for aviation gasolines or aircraft turbine and jet engine fuels of types Jet A, Jet A-1, Jet B, JP-4, JP-5, JP-7, and JP-8.

Note 1: The procedure for the experimental determination of hydrogen in petroleum fractions is described in Test Methods D1018 and D3701.

Note 2: The estimation of the hydrogen content of a hydrocarbon fuel is justifiable only when the fuel belongs to a well-defined class for which a relationship among the hydrogen content and the distillation range, density, and aromatic content has been derived from accurate experimental measurements on representative samples of that class. Even in this case, the possibility that the estimates may be in error by large amounts for individual fuels should be recognized. The fuels used to establish the correlation presented in this test method are defined by the following specifications:

Fuel

Specification

Aviation gasolines

D910

Aircraft turbine and jet engine fuels

 

 JP-4 and JP-5

MIL-T-5624

 JP-6

MIL-J-25056 (Obsolete)

 JP-7

MIL-T-38219

 Jet A

D1655

Miscellaneous hydrocarbons

 No. 2 Diesel fuel

 Kerosine distillates (similar to Jet A)

 Miscellaneous (includes thinners, gasoline fractions, and unidentified blends)

 Special production fuels (commercial products of nearly pure hydrocarbons
  and special high-temperature fuels (HTF) produced for Air Force tests.

 Pure hydrocarbons

1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.4 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ICS
75.160.20 Liquid. Including gasoline, diesel, kerosene, etc. / Жидкое топливо
Сборник ASTM
05.01 Petroleum Products, Liquid Fuels, and Lubricants (I): C1234–D3709 / Нефтепродукты, жидкое топливо и смазочные материалы (I): C1234–D3709
Тематика
Petroleum