Реферат

This specification covers nails, spikes, staples, and other fasteners driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. The driven fasteners are classified as type I: nails (NL); type II: cut nails (CN); type III: spikes (SP); and type IV: staples (ST). Materials shall be tested and the individual types shall conform to the material requirements and physical properties, such as ductility, tensile strength. Protective coating and finishes are also detailed.

Область применения

1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.

Note 1—Fastener ductility information is presented in Table 2 and dimensional information in Tables 3-67.

1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.

1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

TABLE 1 Classification and Identification Index

Type Style Style Identification Table INails (NL) 1. Brads BR 3 2. Barrel BL 4 3. Boat BTH/BTL 5 4. Box A BXA 6 Box B BXB 7 5. Broom BM 8 6. Casing CN 9 7. Cooler CL 10 8. Sinker SK 11 9. Corker CK 12 10. Common CMA 13 Common CMC 14 Common CMS 15 Common CMM 16 11. Concrete CTS/CTM 17 12. Double-headed DH 18 13. Fine FN 19 14. Finishing FH 20 15. Flooring FL 21 16. Lath LHF 22 Lath LHH 23 17. Masonry MR/MRH 24 18. Pallet PL 25 19. Gypsum wallboard GWS 26 Gypsum wallboard GWM 27 20. Roofing RFA 28 Roofing RFS 29 Roofing RFC 30 Roofing RFL 31 Roofing RFR 32 Roofing RFD 33 Roofing RFNS/RFND 34 21. Shingle SHAD/SHAS 35 Shingle SHSS/SHNSB 36 22. Siding SDF/SDC/SDK 37 23. Slating SLA/SLC/SLS 38 24. Rubber heel RH 39 25. Underlayment UL 40 26. Square-barbed SB 41 27. Masonry drive MD 42 28. Escutcheon ES 43 29. Glulam rivet GR 44 30.Post framePF45 IICut nails (CN) 1. Common CM 46 2. Basket BK 47 3. Clout CL 48 4. Trunk TR 49 5. Cobblers CB 50 6. Extra-iron clinching EC 51 7. Hob HB 52 IIISpikes (SP) 1. Common CM 53 2. Gutter GRF/GRO 54 3. Round RDC/RDF 55 4. Barge and boat BB 56 IVStaples (ST) 1. Fence FN 57 2. Poultry netting PN 58 3. Flat top crown FC 59 Flat top crown FCC 60 4. Round or V crown RC 61 5. Preformed PC 62 6. Electrical RE 63 7. Preformed hoop PH 64 8. CapSTC 65

TABLE 2 Bend Angles for Fasteners Using the Test Methods F680 Bend Test

Fastener Material Bend Angle, ° 1. Steel wire: (low-carbon, medium-low
carbon, medium-carbon) (unhardened) 180 2. Stainless steel wire 180 3. Hardened steel fasteners 20 4. Sheet steel for cut nails, Type II,
and cut spikes, Type III 90 5. Copper (min 98 %) 180 6. Copper clad wire (min 20 %) 180 7. Aluminum alloy wire 90 8. Brass wire 180

TABLE 3 Type I, Style 1Brads^A

Note—Steel wire, brad head, diamond point, round smooth shank, bright finish. When specified, brads shall have a modified brad head with a blunt or chiseled point for use with mechanical drivers.

TABLE 4 Type I, Style 2Barrel Nails^A

Note—Steel wire, flat head, diamond point, round smooth shank, bright, zinc or cement coated as specified.

TABLE 5 Type I, Style 3Boat nails^A

Note—Steel wire, oval countersunk head, chisel point, round smooth shank, bright or zinc coated as specified.

TABLE 6 Type I, Style 4ABox Nails^A

Note—Steel wire, flat head, diamond point, round, barbed or smooth shank, bright or cement coated as specified. When specified, box nails shall have an altered or T-head with a diamond, blunt, or chisel point for use with mechanical drivers.

TABLE 7 Type I, Style 4BBox Nails^A

Note—Steel wire, flat head, diamond point, round smooth shank, cement coated.

TABLE 8 Type I, Style 5Broom Nails^A

Note—Steel wire, flat or star head, diamond point, round smooth shank, bright finish, as specified.

TABLE 9 Type I, Style 6Casing Nails^A

Note—Steel wire, flat countersunk cupped head, diamond point, round smooth shank, bright finish.

TABLE 10 Type I, Style 7Cooler Nails^A

Note—Steel wire, flat head, diamond point, round smooth shank, cement coated. When specified, coolers shall have an altered or T-head for use with mechanical drivers.

TABLE 11 Type I, Style 8Sinker Nails^A

Note—Steel wire, flat countersunk head, diamond point, round smooth shank, bright or cement coated. When specified, sinkers shall have an altered or T-head for use with mechanical drivers.

TABLE 12 Type I, Style 9Corker Nails^A

Note—Steel wire, flat countersunk head, diamond point, round smooth shank, cement coated. When specified, corkers shall have an altered or T-head for use with mechanical drivers.

TABLE 13 Type I, Style 10Common Nails^A

Note—Aluminum alloy wire, flat head, diamond point, round smooth shank, or, when specified, square barbed shank.

TABLE 14 Type I, Style 10Common Nails^A

Note—Copper wire, flat head, diamond point, round smooth shank.

TABLE 15 Type I, Style 10Common Nails^A

Note—Steel wire, flat head, diamond point, round smooth shank, bright, zinc or cement coated as specified.

TABLE 16 Type I, Style 10Common Nails^A

Note—Aluminum alloy wire, stainless steel or steel wire, (bright, zinc coated or cement coated), altered or T-head, diamond or chisel point, round smooth or deformed shank, as specified. For use with mechanical drivers.

F1667 NLCMM Dash No.LDDash No.LDDash No.LDDash No.LDDash No.LDDash No.LD 011 ¼0.080151 ¾0.0862920.148431 ¾0.120572³/₈0.1137130.131 021 ¼0.086161 ¾0.092302 ¼0.092441⁷/₈0.120582³/₈0.1207230.148 031 ¼0.092171 ¾0.099312 ¼0.099451⁷/₈0.131592³/₈0.131733 ¼0.120 041 ¼0.099181 ¾0.113322 ¼0.113461⁷/₈0.148602³/₈0.148743 ¼0.131 051 ½0.080191⁷/₈0.080332 ½0.0924720.120612 ½0.120753 ¼0.148 061 ½0.086201⁷/₈0.086342 ½0.0994820.131622 ½0.148763 ½0.135 071 ½0.092211⁷/₈0.092352 ½0.113492¹/₈0.099632 ½0.162773 ½0.148 081 ½0.099221⁷/₈0.099362 ½0.131502¹/₈0.113642⁵/₈0.148783 ½0.162 091 ½0.113231⁷/₈0.113373 ½0.131512¹/₈0.120652 ¾0.1207940.148 101⁵/₈0.0802420.080381 ½0.120522¹/₈0.131662 ¾0.1318040.162 111⁵/₈0.0862520.086391 ½0.131532¹/₈0.148672 ¾0.148814 ½0.148 121⁵/₈0.0922620.092401 ½0.148542 ¼0.120682⁷/₈0.120824 ½0.162 131⁵/₈0.0992720.099411 ½0.162552 ¼0.1316930.120......... 141 ¾0.0802820.113421⁵/₈0.113562 ¼0.1487030.128.........

TABLE 17 Type I, Style 11Concrete Nails^A

Note—Harded steel, flat countersunk head, diamond point, smooth or mechanically deformed shank formed from round or square stock, as specified, bright finish.

TABLE 18 Type I, Style 12Double-Headed Nails^A

Note—Steel wire, flat heads, diamond point, round smooth shank, bright finish or cement coated.

TABLE 19 Type I, Style 13Fine Nails^A

Note—Steel or copper wire, flat head, diamond point, round smooth shank, bright finish.

TABLE 20 Type I, Style 14Finish Nails^A

Note—Steel wire, brad head, altered or clipped T-head for use with mechanical drivers, diamond or chisel point, smooth or barbed shank formed from round or square stock, as specified, bright finished.

TABLE 21 Type I, Style 15Flooring Nails^A

Note—Harded steel or steel wire, casing head or flat-cupped countersunk head, diamond or blunt point, round, smooth or mechanically deformed shank, dark (hardened), bright (steel wire) or cement coated, as specified.

TABLE 22 Type I, Style 16Lath Nails^A

Note—Steel wire, flat head, diamond point, round smooth shank, blued finish.

TABLE 23 Type I, Style 16Lath Nails^A

Note—Steel wire, flat hook-head, diamond point, round smooth shank, bright, blued, or zinc coated as specified.

TABLE 24 Type I, Style 17Masonry Nails^A

Note—Hardened steel, flat or flat countersunk head, diamond point, mechanically deformed shank, bright finish.

TABLE 25 Type I, Style 18Pallet Nails^A

Note—Hardened steel or steel wire (for mechanical drivers); flat head, altered or T-Head (for mechanical drivers); diamond, blunt diamond, blunt chisel or blunt point; round, mechanically deformed shank; bright finish (steel wire); or dark (hardened), as specified.

Dash No.LDHNo. /LbDash No.LDHNo. Lb 011½0.1200.281190311¾0.0990.255 262 021⁵/₈0.1200.281170321¾0.0990.280 262 0320.1200.2811403320.0840.200 318 042¼0.1200.2811303420.0860.235 304 052½0.1200.2811203520.0900.245 277 062½0.1350.31293362 0.0990.255 229 0730.1200.281983720.0990.280 229 0830.1350.312793820.1050.270204 0930.1480.312663920.1130.280176 103¼0.1350.31273402¼ 0.0840.200283 113¼0.1480.31261412¼0.0860.235270 123½0.1480.31257422¼0.0990.255204 133½0.1620.37547432¼0.0990.280204 143½0.1770.43838442¼0.1050.270181 1540.1770.43835452¼0.1130.280156 1640.1770.37535462½0.0950.260199 1750.1770.37527472½0.0990.255183 1860.1770.37523482½0.0990.280183 1970.2070.50015492½ 0.1130.280141 2080.2070.50013502½ 0.1130.290141 211¼0.080 0.215561512½0.1200.290125 221¼0.0990.255 367522½0.1310.280105 231¼0.0990.280 367532¾0.1130.290128 241½0.0800.215 468542¾0.1200.285113 251½0.0990.255 3055530.1130.280117 261½0.0990.280 305563¼0.1200.29096 271⁵/₈0.1050.270 251573¼0.1310.28081 281¾ 0.0840.200 364583½ 0.1310.28075 291¾0.0860.235 347594 0.1200.28078 301¾ 0.0900.245 3176040.1310.28065

^A All dimensions are given in inches.

TABLE 26 Type I, Style 19Gypsum-Wallboard, Gypsumboard, and Drywall Nails^A

Note—Steel wire, flat head, diamond point, round smooth or deformed shank, bright or blued finish.

TABLE 27 Type I, Style 19Gypsum-Wallboard, Gypsumboard, and Drywall Nails^A

Note—Steel wire, flat slightly countersunk head, long diamond point, round mechanically deformed shank, bright or blued finish.

TABLE 28 Type I, Style 20Roofing Nails^A

Note—Aluminum alloy wire, flat head, diamond point, round smooth shank, or, when specified, square-barbed shank.

TABLE 29 Type I, Style 20Roofing Nails^A

Note—Steel wire; flat head; diamond point; round, smooth or deformed shank; bright or zinc coated, as specified, for hand driving or for use with mechanical drivers.

Dash NoLDHNo./lbDash No.LDHNo./lb 01¾0.1060.375460341¼0.1480.500140 02¾0.1200.438340351¼0.1620.500120 03¾0.1350.469270361½0.1060.375... 04¾0.1420.484240371½0.1200.438180 05¾0.1480.500220381¼0.1200.500160 06¾0.1620.500200391¼0.1350.469150 07⁷/₈0.1060.375...401½0.1420.484130 08⁷/₈0.1200.438300411½0.1480.500120 09⁷/₈0.1200.500250421½0.1620.500110 10⁷/₈0.1350.469240431¾0.1060.375220 11⁷/₈0.1420.484210441¾0.1200.438160 12⁷/₈0.1480.500190451¾0.1200.500140 13⁷/₈0.1620.500170461¾0.1350.469130 1410.1060.281380471¾0.1420.484120 1510.1060.375360481¾0.1480.500110 1610.1200.438270491¾0.1620.50092 1710.1200.50022050¾0.1200.375290 1810.1350.46921051⁷/₈0.1200.375259 1910.1420.4841905210.1200.375232 2010.1480.500170531¼0.1200.375209 2110.1620.500150541½0.1200.375179 221¹/₈0.1060.375320551¾0.1200.375157 231¹/₈0.1200.4382405620.1200.375156 241¹/₈0.1350.4691905720.1200.438156 251¹/₈0.1420.484170582½0.1200.375125 261¹/₈0.1480.500160592½0.1200.438125 271¹/₈0.1620.5001406030.1200.375104 281¼0.1060.3753006130.1200.438104 291¼0.1200.312240623½0.1200.37589 301¼0.1200.438220633½0.1200.43889 311¼0.1200.500...6440.1200.37578 321¼0.1350.4691806540.1200.43878 331¼0.1420.4841606630.1350.37572 341¼0.1480.500140673½0.1350.37562 351¼0.1620.5001206840.1480.40646 361½0.1060.375...694½0.1480.40640

^A All dimension are given in inches.

TABLE 30 Type I, Style 20Roofing Nails^A

Note—Copper-clad wire, flat head, diamond point, round smooth shank.

TABLE 31 Type I, Style 20Roofing Nails^A

Note—Steel wire; leak-resistant umbrella head; diamond point; round smooth or deformed shank; zinc coated.

Dash. No.LDHNo./Lb 11¾0.1350.500110 220.1350.50098 320.1350.75073 420.1480.75062 520.1480.81360 62½0.1350.75064 72½0.1480.75053 82½0.1480.81353 930.1480.81347

^A All dimensions are given in inches.

TABLE 32 Type I, Style 20Roofing Nails^A

Note—Steel wire, flat reinforced head, needle or diamond point, round smooth shank, bright or zinc coated, as specified. (For prepared felt roofing.)

TABLE 33 Type I, Style 20Roofing Nails^A

Note—Hand-driven cap nails shall have a 1 in. diameter round plastic or steel cap with a cap diameter tolerance of ± 0.063 in., or a flat or domed square steel cap with an edge dimension 1 ± 0.063 in. Minimum thickness of the outside edge of plastic caps shall be 0.035 in. Minimum thickness of metal caps shall be 0.030 in.^† Nails are steel or stainless steel; with a diamond point; smooth or deformed shanks from round or spiral wire; and bright or zinc finish. Nails with metal caps shall both be bright or both have zinc finish. All hand-driven cap nails are packaged as integral nail-cap units.

F1667 NLRFD No/Lb^B Dash No.LDSteelPlastic Hand Driven 01½0.105130 02⁵/₈0.105120 03¾0.105115362 04⁷/₈0.105110339 0510.105110323 061¹/₈0.105110 071¼0.105100269 08not used 09not used 10not used 11not used 1230.10670118 1330.1205070 141½0.10596219 151½0.12085175 161¾0.10594195 171¾0.12080152 1820.10590169 1920.12074131 202½0.10580138 212½0.1206195 223½0.14853 2340.14832 2450.16225 2560.16220 2680.16213

^A All dimensions are given in inches.

^B Dashes () indicate that the fastener size is not a standard size.

^† Editorially corrected in March 2012.

TABLE 34 Type I, Style 20Roofing Nails^A

Note—Power driven cap nails have a 1 in. diameter plastic or steel cap with a cap diameter tolerance of ± 0.063 in. Minimum thickness of the outside edge of plastic caps is 0.035 in. Minimum thickness of metal caps is 0.010 in. Nails are steel or stainless steel; with a diamond point; smooth or deformed shanks from round or spiral wire; and bright or zinc finish. Nails with metal caps shall both be bright or both have zinc finish. With power driven cap nails, nails and caps may be packaged together or separately. Regardless of packaging, nails and caps are separately loaded into application tools with the nail being driven through the cap at point of application.

The nails used in the power driven cap nail systems are not considered roofing nails until they are combined with the cap.

F1667 NLRFD No/Lb^B Dash No.LDSteelPlastic Power Driven 27¾0.120185268 28⁷/₈0.083200400 29⁷/₈0.120168240 3010.083196355 3110.120154215 321¼0.080320 331¼0.083190310 341¼0.120140190 351½0.080290 361½0.083183280 371½0.120126165 381¾0.083176265 391¾0.120106140 4020.083170250 4120.091230 4220.12082114

^A All dimensions are given in inches.

^B Dashes () indicate that the fastener size is not a standard size.

TABLE 35 Type I, Style 20Roofing Nails^A

Note—Aluminum alloy wire, flat head with neoprene washer (for aluminum roofing sheet), diamond point, round, smooth, or mechanically deformed shank, as specified.

TABLE 36 Type I, Style 21Shingle Nails^A

Note—Aluminum Alloy wire, flat head, diamond point, round, smooth or mechanically deformed shank, as specified.

TABLE 37 Type I, Style 21Shingle Nails^A

Note—Steel wire, flat head, diamond point, round, smooth (standard) or barbed (for special shingles) shank, bright or zinc coated, as specified.

TABLE 38 Type I, Style 22Siding Nails^A

Note—Aluminum alloy wire, flat head (insulated), casing or countersunk head (wood), as specified, diamond point, round smooth shank or, when specified, square-barbed shank.

TABLE 39 Type I, Style 23Slating Nails^A

Note—Aluminum alloy, copper or steel wire as specified. Aluminum and copper nails shall have a flat head (0.312 to 0.375–in. diameter), diamond point, and round smooth shank or, when specified, square-barbed shank. Steel nails shall have a flat, slightly countersunk head, diamond point, round smooth shank, zinc coated.

TABLE 40 Type I, Style 24Rubber Heel Nails^A

Note—Steel wire, flat or countersunk head, as specified, needle point, round smooth shank, bright finish.

TABLE 41 Type I, Style 25Underlayment Nails^A

Note—Steel wire, flat or flat, slightly countersunk head, diamond point, round, mechanically deformed shank, bright finish.

TABLE 42 Type I, Style 26Barbed Nails^A

Note—Steel wire, flat head, diamond point, square barbed shank, bright finish.

TABLE 43 Type I, Style 27Masonry Drive Nails^A

Note—Hardened steel, flat head, cone pilot point, round, high pitch, multiple-start threaded shank, bright finish. When specified, masonry drive nails shall be proof lead tested.

TABLE 44 Type I, Style 28Escutcheon Nails^A

Note—Steel or brass wire, as specified, oval head, diamond point, round smooth shank.

TABLE 45 Type I, Style 29Glulam Rivet^A

Note—Hardened steel, flat countersunk head, diamond point, smooth shank, zinc coated, as specified.

TABLE 46 Type I, Style 30Post-Frame Shank Nails^A

Note—Steel, flat head, diamond point, round, mechanically deformed shank, bright or zinc-coated as specified. Nails shall comply with the supplementary requirements of S1 and Table S1.2.

Dash No.LDHT1–D
maxT1–D
minTL
minP_maxP_minRoot Diameter^B 01 30.135⁵/₁₆.010.0052.25.077.0500.128 0230.148⁵/₁₆.010.0052.25.077.0500.140 0330.177³/₈.010.0052.25.077.0500.169 043.50.135⁵/₁₆.010.0052.25.077.0500.128 053.50.148⁵/₁₆.010.0052.25.077.0500.140 063.50.177³/₈.010.0052.25.077.0500.169 073.50.200¹⁵/₃₂.010.0052.25.077.0500.193 0840.148⁵/₁₆.010.0052.25.077.0500.140 0940.177³/₈.010.0052.25.077.0500.169 1040.200¹⁵/₃₂.010.0052.25.077.0500.193 1140.207¹⁵/₃₂.010.0052.25.077.0500.199 124.50.148⁵/₁₆.010.0053.077.0500.140 134.50.177³/₈.010.0053.077.0500.169 144.50.200¹⁵/₃₂.010.0053.077.0500.193 154.50.207¹⁵/₃₂.010.0053.077.0500.199 1650.177³/₈.010.0053.077.0500.169 1750.200¹⁵/₃₂.010.0053.077.0500.193 1850.207¹⁵/₃₂.010.0053.077.0500.199 1960.177³/₈.010.0053.077.0500.169 2060.200¹⁵/₃₂.010.0053.077.0500.193 2160.207¹⁵/₃₂.010.0053.077.0500.199 2280.177³/₈.010.0053.077.0500.169 2380.200¹⁵/₃₂.010.0053.077.0500.193 2480.207¹⁵/₃₂.010.0053.077.0500.199

^A All dimensions are given in inches.

^B Root diameter is a calculated value and is not specified as a dimension to be measured.

L= length, in., H= head diameter, in., TL= length of threaded shank, in., max= maximum acceptable value (not subject to tolerances), min= minimum acceptable value (not subject to tolerances), D= shank diameter, in., T1= crest diameter, in., and P= pitch, or spacing of threads, in.

TABLE 47 Type II, Style 1Common Cut Nails^A

Note—Steel or copper, flat head, bright finish.

TABLE 48 Type II, Style 2Basket Cut Nails^A

Note—Steel, flat head, bright finish.

TABLE 49 Type II, Style 3Clout Cut Nails^A

Note—Steel, flat head, bright finish, blued or zinc coated, as specified (see 5).

TABLE 50 Type II, Style 4Trunk Cut Nails^A

Note—Steel, oval head, bright finish, blued, brass or copper plated, as specified.

TABLE 51 Type II, Style 5Cobblers Cut Nails^A

Note—Steel casing head, clinch point, bright finish or brass plated, as specified.

TABLE 52 Type II, Style 6Extra-Iron Clinching Cut Nails^A

Note—Steel, casing head, clinch point, bright finish or blued, as specified.

TABLE 53 Type II, Style 7Hob Cut Nails^A

Note—Steel, square grooved head, clinch point, bright finish, or blued, as specified.

TABLE 54 Type III, Style 1Common Spikes^A

Note—These spikes shall be sheared from medium carbon sheet steel and shall have a wedged-shaped shank with a square point end narrower than the upset head end. They shall have a flat head, bright finish, or zinc coated, as specified.

TABLE 55 Type III, Style 2Gutter Spikes^A

Note—Steel wire, oval head, chisel point, flat head, diamond point, bright finish or zinc coated, as specified.

TABLE 56 Type III, Style 3Round Spikes^A

Note—Steel wire, oval countersunk head, chisel point, flat head, diamond point, bright finish or zinc coated, as specified.

F1667 SPRDC^AF1667 SPRDF^A Dash No.SLDHDash No.LDH 0140d50.26250.5310180.3120.625 0250d5½0.2830.5620280.3120.750 0360d60.2830.5620390.3120.750 04. . .70.3120.62504100.3120.750 . . .. . .. . .. . .. . .0580.3750.750

^A All dimensions are given in inches.

TABLE 57 Type III, Style 4Barge and Boat Spikes^A

Note—Wrought iron, hot rolled steel rod or steel wire, square, diamond or oval head, chisel point, bright finish or zinc coated, as specified.

TABLE 58 Type IV, Style 1Fence Staples^A

Note—Steel wire, bright finish or zinc coated, as specified.

TABLE 59 Type IV, Style 2Poultry Netting Staples^A

Note—Steel wire, zinc coated.

TABLE 60 Type IV, Style 3Flat Top Crown Staples^A

Note—Steel wire, aluminum alloy wire, bright finish, zinc coated, cement coated or chemically etched, as specified. (For use in power tools for fastening wood and other materials to wood.)

TABLE 62 Type IV, Style 3Flat Top Crown Staples^A

Note—Steel wire, chisel point, tin plated, zinc coated or lacquer finish, as specified, cohered together in strips. (For use in staple tackers or machines.) The number per strip shall be as specified and shall be suitable for use in the make and model of tool specified.

TABLE 63 Type IV, Style 4Round or “V” Crown Staple ^A

Note—Steel wire or copper-clad wire, bright finish, zinc coated, cement coated or chemically etched, as specified. (For use in power tools for fastening wood and other materials to wood.)

TABLE 64 Type IV, Style 5Preformed Staples^A

Note—Steel wire, chisel point, zinc or cement coated, as specified. Copper-clad wire, chisel point, tinned or other plated finish, as specified. (Hand driven.)

TABLE 65 Type IV, Style 6Electrical Staples^A

Note—Insulated or uninsulated, as specified.

TABLE 66 Type IV, Style 7Preformed Hoop Staple^A

TABLE 67 Type IV, Style 8-Cap Staples

Note—Cap staples are Type IV, Style 3, steel, flat top crown, with bright finish or zinc coated (as specified) staples, with a 1 in. diameter plastic cap having a cap diameter tolerance of ± 0.025 in. Minimum thickness of the outside edge of plastic caps is 0.035 in. Staples are driven with a hand (swung) or power tool with the staple being driven though the cap at point of application. Staples and caps may be packaged together or separately. Regardless of packaging, nails and caps are separately loaded into application tools with the staple being driven through the cap at point of application.

STC Staples-Cap Sets Dash No.Ga.CL 118³/₁₆¾ 218³/₁₆⁷/₈ 318³/₁₆1 418³/₁₆1–¹/₈ 518³/₁₆1–³/₁₆ 618³/₁₆1–½ 718⁵/₁₆¾ 818⁵/₁₆⁷/₈ 918⁵/₁₆1 1018⁵/₁₆1–¹/₈ 1118⁵/₁₆1–³/₁₆ 1218⁵/₁₆1–½ 1318³/₈⁵/₈ 1418³/₈¾ 1518³/₈⁷/₈ 1618³/₈1 1718³/₈1–¹/₈ 1818³/₈1–¼ 1918³/₈1–³/₈ 2018³/₈1–½ 2118⁷/₁₆⁵/₈ 2218⁷/₁₆¾ 2318⁷/₁₆⁷/₈ 2418⁷/₁₆1 2518⁷/₁₆1–¹/₈ 2618⁷/₁₆1–¼ 2718⁷/₁₆1–³/₈ 2818⁷/₁₆1–½ 2920³/₈⁵/₈ 3021½⁵/₈ 3124³/₈³/₈