Каталог стандартов

+7 (495) 223-46-76 +7 (812) 309-78-59
inform@normdocs.ru

ASTM F406-02

Заменен
Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards — 18 стр.
Область применения

1.1 This consumer safety specification establishes testing requirements for structural integrity and performance requirements for non-full-size cribs/play yards, both rigid sided and mesh/fabric assemblies. It also provides requirements for labeling and instructional material. The term unit or product will refer to a non-full-size crib/play yard.

1.2 This specification covers products intended to provide sleeping and playing accommodations for a child (excluding bassinets, cradles, and baskets) that have an interior length dimension smaller than 49¾ in. (1263 mm) or an interior width dimension smaller than 25 3/8 in. (643 mm), or both. Such products are intended for a child who is less than 35 in. (890 mm) in height.

1.3 No product produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein, before and after all testing.

1.4 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.

1.5 The following safety hazards caveat pertains only to the test method portion, Section 8 , of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1 - This consumer safety specification includes the following sections:

TitleSectionScope1Referenced Documents2ASTM Standards2.1Federal Regulations2.2Terminology3Definitions of Terms Specific to This Standard 3.1Conspicuous3.1.1Cord3.1.2Dropside/Dropgate3.1.3Dynamic Load3.1.4Fabric3.1.5Foldable Side or End3.1.6Manufacturer's Recommended Use Position 3.1.7Mattress3.1.8Mesh3.1.9Mesh/Fabric Crib3.1.10Nonpaper Label3.1.11Occupant3.1.12Paper Label3.1.13Protrusion3.1.14Rigid Sided Crib3.1.15Seam3.1.16Static Load3.1.17Stationary Side3.1.18Structural Failure3.1.19Calibration and Standardization4General Requirements5Scissoring, Shearing, or Pinching5.6Latching and Locking Mechanisms5.7Openings5.8Protective Components5.9Labeling5.10Stability5.11Cord Length5.12Coil Springs5.13Mattress5.14Protrusions5.15Performance Requirements for Rigid Sided Units 6Vertical Impact Testing6.2Mattress Support Testing6.2.4Side or End Testing, or Both6.2.2Mattress Support System Testing6.3Side(s) and/or End(s) Latch Testing6.4Dropside Latch Testing6.4.1Foldable Side or End Latch Testing 6.4.2Plastic Teething Rail6.5Performance Requirements for Mesh/Fabric Units 7Height of Sides7.1Side Deflection and Strength7.2Floor Strength7.3Locking Device7.4Top Rail Covering Material7.5Mesh Requirements7.6Mesh Openings7.6.1Mesh Strength7.6.2Fabric Material Requirements7.7Fabric Strength7.7.1Mesh/Fabric Assembly Requirements7.8Sewn Assembly7.8.1Seam Strength7.8.2Mesh/Fabric Attachment Strength 7.8.3Test Methods8Mattress Support Impact Test for Rigid Sided Cribs8.1Side or End Impact Test, or Both, for Rigid Sided Cribs8.2Dropside Impact Test8.2.2Dropside Static Test8.2.3Stationary Side or Foldable Side Impact Test8.2.4Stationary Side or Foldable Side Static Test8.2.5Mattress Support System Test for Rigid Sided Cribs8.3Side or End Latch Test, or Both, for Rigid Sided Cribs8.4Test Method for Dropside Latch 8.4.2Procedure for Vertical Dropside Latch Tests8.4.3Procedure for Horizontally Hinged Dropside Latch Test8.4.4Test Procedure for Latches to Prevent Folding of a Foldable Side or End8.4.5Plastic Teething Rail Test for Rigid Sided Cribs8.5Procedure for Plastic Teething Rail Test8.5.2Side Deflection and Strength Tests for Mesh/Fabric Cribs8.6Floor Strength Test for Mesh/Fabric Cribs 8.7Locking Mechanism Test8.8Dropside Locking Device Test Method 8.8.1Folding Latch Test Method8.8.2Mesh Opening Test8.9Test for Strength of Mesh and Integrity of Attachment8.10Mesh/Fabric Attachment Strength Test Method 8.11Test for Stability of Product8.12Permanency of Labels and Warnings8.13Removal of Protective Components8.16Torque Test8.16.3Tension Test8.16.4Vinyl Thickness Measurement8.17Test for Attachment of Storage Pouch or Other Parts with Printed Warnings8.18Cord Length Test Method8.19Protrusions8.20Marking and Labeling9Labeling9.1Warning Statements9.2Instructional Literature10Warning Statements10.1.2Water Mattress Use10.3.4

ICS
97.220.30 Indoor. Including equipment for gymnastics, volleyball, basketball, handball, home sports trainers, etc. / Инвентарь для спортивных залов. Включая инвентарь для гимнастики, волейбола, баскетбола, гандбола, домашние тренажеры и т.д.
97.220.40 Outdoor. Including equipment for mountaineering, football, tennis, swimming, diving, etc. / Инвентарь для спорта на открытом воздухе и для водных видов спорта. Включая инвентарь для альпинизма, футбола, тенниса, плаванья, погружения в воду и т.д.
Сборник ASTM
15.11 Consumer Products; Business Imaging Products; Vacuum Cleaners / Потребительские товары; Имиджевая бизнес-продукция; Уборочные машины вакуумного действия
Тематика
Consumer Product Evaluation