Каталог стандартов

+7 (495) 223-46-76 +7 (812) 309-78-59
inform@normdocs.ru

ASTM F842-14

Заменен
Standard Test Methods for Measuring the Forced Entry Resistance of Sliding Door Assemblies, Excluding Glazing Impact — 16 стр.
Значение и использование

5.1 These test methods are intended to establish a measure of resistance for sliding door assemblies subjected to attacks (other than impacting glazing materials) by unskilled or opportunistic burglars. Resistance to higher levels of force generated by skilled burglary attack requires methods, such as alarms, communication, or apprehension systems, or special security glazing materials more sophisticated than those evaluated by these test methods. Technicians performing the test should understand the intent of this test method and should be trained on the execution and pass/fail criteria.

5.2 Entry through a sliding door assembly can be accomplished by impacting or removing glazing materials. This method does not evaluate glazing materials for breakage or de-glazing. Other standards must be used to evaluate forced entry by impacting or removing glazing.

5.3 Acceptance criteria for performance levels are a matter for authorities having specific jurisdiction to establish. Suggested guidelines are found in Annex A1.

Область применения

1.1 These test methods determine the ability of sliding door assemblies to restrain, delay, or frustrate forced entry.

1.2 For purposes of these test methods, sliding door assemblies are defined as described in 1.2.1 – 1.2.4 and as shown in Fig. 1. Sliding door assemblies with a combination of operable panels and fixed panels (lites) shall be classified and tested separately for each type.

1.2.1 Type A—A sliding door assembly which incorporates one or more sliding panels that lock to the jamb.

1.2.2 Type B—A sliding door assembly which incorporates one or more sliding panels that lock to an intermediate jamb.

1.2.3 Type C—A sliding door assembly which incorporates one or more sliding panels that abut and lock to other panels.

1.2.4 Type D—A sliding door assembly which incorporates one or more fixed or stationary panels that are designed not to open.

Note 1See Fig. 1 for graphic depiction of sliding door assembly types.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ICS
13.310 Protection. Including security services, security procedures, burglar alarm devices, burglary resisting materials and equipment, bullet resisting materials and equipment, anti-theft devices for vehicles, safes, strong rooms, etc. / Защита от преступлений. Включая услуги по обеспечению безопасности, процедуры обеспечения безопасности, устройства тревожной сигнализации против взлома, материалы и оборудование для защиты от взлома, пуленепробиваемые материалы и оборудование, противоугонные устройства для транспортных средств, сейфы, комнаты-сейфы и т.д.
91.060.50 Doors. Including doorsets, their components, blinds, shutters / Двери и окна. Включая дверные блоки, их компоненты, жалюзи, ставни
Сборник ASTM
04.12 Building Constructions (II): E2112-latest; Sustainability; Asset Management; Technology and Underground Utilities / Строительство зданий (II): с E2112 и далее; Устойчивость; Система управления недвижимостью (системы эксплуатации зданий и сооружений); Технологии и Подземные коммуникации
Тематика
Buildings