Каталог стандартов

+7 (495) 223-46-76 +7 (812) 309-78-59
inform@normdocs.ru
О компании Стандарты Контакты Заказать стандарт
СтандартыBSI

BS EN ISO 20029-2:2018

Действует
Plastics. Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion. Preparation of test specimens and determination of properties — 26 стр.
ОписаниеИзмененияСсылкиВерсии

Ссылочные документы

ISO 4589-2:1996/Amd.1:2005
Заменен
Plastics -- Determination of burning behaviour by oxygen index -- Part 2: Ambient-temperature test -- Amendment 1 — 8 стр.
ISO 20753:2008
Заменен
Plastics -- Test specimens — 22 стр.
IEC 60112:2003 ed4.0
Заменен
Method for the determination of the proof and the comparative tracking indices of solid insulating materials — 21 стр.
ISO 20029-1:2017
Действует
Plastics -- Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion -- Part 1: Designation system and basis for specification — 18 стр.
ISO 15512:2016
Действует
Plastics -- Determination of water content — 32 стр.
BS ISO 815-1:2014
Действует
Rubber, vulcanized or thermoplastic. Determination of compression set. At ambient or elevated temperatures — 20 стр.
ASTM E968-02(2014)
Отменен
Standard Practice for Heat Flow Calibration of Differential Scanning Calorimeters (Withdrawn 2023) — 5 стр.
ISO 22007-2:2008
Заменен
Plastics -- Determination of thermal conductivity and thermal diffusivity -- Part 2: Transient plane heat source (hot disc) method — 24 стр.
ISO 8689-2:2000
Действует
WATER QUALITY. BIOLOGICAL CLASSIFICATION OF RIVERS. PART 2. GUIDANCE ON THE PRESENTATION OF BIOLOGICAL QUALITY DATA FROM SURVEYS OF BENTHIC MACROINVERTEBRATES — 10 стр.
ISO 179-2:1997/Amd.1:2011
Действует
Plastics -- Determination of Charpy impact properties -- Part 2: Instrumented impact test -- Amendment 1: Precision data — 8 стр.
BS ISO 6281:2007
Действует
Plain bearings. Testing under conditions of hydrodynamic and mixed lubrication in test rigs — 24 стр.
ISO 294-4:2001
Действует
Plastics. Injection moulding of test specimens of thermoplastic materials. Part 4. Determination of moulding shrinkage — 16 стр.
ISO 294-1:1996/Amd.2:2005
Заменен
Plastics -- Injection moulding of test specimens of thermoplastic materials -- Part 1: General principles, and moulding of multipurpose and bar test specimens -- Amendment 2: Methods of determining the hold pressure and hold time — 12 стр.
IEC 60243-1:1988/COR1:1989 ed1.0
Заменен
Corrigendum 1 - Methods of test for electric strength of solid insulating materials. Part 1: Tests at power frequencies — 1 стр.
ISO 974:2000
Действует
Plastics - Determination of the brittleness temperature by impact — 12 стр.
IEC 60695-11-10:1999 ed1.0
Заменен
Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods — 45 стр.
IEC 60093:1958/COR1:1958 ed1.0
Заменен
Corrigendum 1 - Recommended methods of test for volume and surface resistivities of electrical insulating materials — 0 стр.
ISO 17892-3:2015
Действует
Geotechnical investigation and testing -- Laboratory testing of soil -- Part 3: Determination of particle density — 20 стр.
ISO 11359-2:1999
Действует
Plastics - Thermomechanical analysis (TMA) - Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature — 16 стр.
ISO 34-1:2015
Действует
Rubber, vulcanized or thermoplastic -- Determination of tear strength -- Part 1: Trouser, angle and crescent test pieces — 20 стр.
ISO 899-1:2017
Действует
Plastics -- Determination of creep behaviour -- Part 1: Tensile creep — 20 стр.
BS ISO 3069:2000
Действует
End-suction centrifugal pumps. Dimensions of cavities for mechanical seals and for soft packing — 18 стр.
IEC 60250:1969 ed1.0
Заменен
Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths — 56 стр.
ISO 75-2:2013
Действует
Plastics -- Determination of temperature of deflection under load -- Part 2: Plastics and ebonite — 16 стр.
ISO 22007-3:2008
Действует
Plastics -- Determination of thermal conductivity and thermal diffusivity -- Part 3: Temperature wave analysis method — 24 стр.
ISO 11357-3:2018
Действует
Plastics -- Differential scanning calorimetry (DSC) -- Part 3: Determination of temperature and enthalpy of melting and crystallization — 12 стр.
BS ISO 16365-2:2014
Действует
Plastics. Thermoplastic polyurethanes for moulding and extrusion. Preparation of test specimens and determination of properties — 20 стр.
ISO 10350-1:2007
Заменен
Plastics -- Acquisition and presentation of comparable single-point data -- Part 1: Moulding materials — 18 стр.
ISO 3167:2014
Действует
Plastics -- Multipurpose test specimens — 14 стр.
ISO 8256:2004
Действует
Plastics -- Determination of tensile-impact strength — 22 стр.
BS EN ISO 14910-2:2013
Заменен
Plastics. Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion. Preparation of test specimens and determination of properties — 26 стр.

На этот документ ссылаются

BS EN ISO 14910-2:2013
Заменен
Plastics. Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion. Preparation of test specimens and determination of properties — 26 стр.